background image

Specifications                                                                                        ICEU060

Page 2

Specifications:

 24 Hour

Bin Storage

  Basic

Maximum 

Ref Type.

Model Number

Capacity

 Capacity

Electrical

Fuse Size

Ounces 

ICEU060

               55 lbs.

  28 lbs.

115/60/1

      15

R134a, 9.5 oz

Operating Requirements

:

Minimum

Maximum

Air Temperature

50

°

 F

100

°

 F

Water Temperature

40

°

 F

100

°

 F

Water Pressure

20 PSIG

100 PSIG

Voltage

103.5 V

126.5 V

Ice-O-Matic ice machines are not designed for outdoor installations.  

Machine requires voltage indicated on rating nameplate.  Failures caused by improper voltage are
not considered factory defects.  Extended periods of operation at temperatures exceeding
limitations constitutes misuse under the terms of the Ice-O-Matic Manufacture’s Limited Warranty,
resulting in a loss of warranty coverage.  Specifications and design are subject to change without
notice.

The ICEU060 ice machine has a 3 year Parts Warranty and a 3 year Labor Warranty.
The Compressor and Evaporator have a 5 year Parts Warranty
Ice-O-Matic recommends the installation of water filters.

Summary of Contents for ICEU060




















Reviews: