10
ICE i20NB / i20NBT / i20NBT-OB / i24BT
OPERATOR MANUAL
daIly maIntenance
1. Remove pad driver/ brush and clean with
approved cleaner.
2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check
the recovery tank for debris and clean out as
necessary.
3.
Raise the squeegee assembly off floor and wipe
it down with a damp towel. Be sure to store the
squeegee in the up position.
4.
Remove the float shut-off assembly and rinse it
out with clean water.
5. Clean machine with an approved cleaner and a
damp towel.
6. Recharge the batteries.
7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
montHly maIntenance
1. Clean the battery tops to prevent corrosion.
2. Check for loose battery cable connections.
3. Inspect and clean the recovery tank cover seal.
Replce it if damaged.
4. Lubricate all grease points and pivot points with
silicon spray and approved grease.
5. Check the machine for loose nuts and bolts.
6. Check the machine for leaks.
oRBItal Head maIntenance
For Orbital head, you should have checked the
eight isolators located in the Orbital head every
300 hours.
1.
Using a flashlight, do a visual inspection of the
isolators by looking through the opening in the
Orbital head and checking for wear or damage
to four isolators in the front and four in the
rear of the Orbital head. The locations of the
isolators are show below.
2. If any of the eight isolators show signs of wear,
degradation or damage, contact your lacal
distributor to replace all eight isolators.
motoR maIntenance
1. Contact your local Distributor for any motor
maintenance.
2. Motor should have the brushes checked every
250 hours. Brushes should be replaced when
they are worn to a length of 10 mm or less.
BatteRy maIntenance
WaRnInG: Batteries emit hydrogen gas
and an explosion o fire can result. Keep sparks
and fire away from batteries at all times.
WARNING: Whenever serviving batteries,
be sure to wear protective gloves. Avoid
contact with battery acid at all times.
NOTE:
For the best machine performance, keep
batteries charged at all times. Do not let them sit in
a discharged condition.
1. Always follow the battery charging directions as
outlined in the BATTERY CHARGING section of
this manual.
2. Keep battery tops and terminals free from
corrosion. A strong solution of baking soda
and water is the best way to keep the batteries
corrosion free. DO NOT ALLOW THE BAKING
SODA / WATER SOLUTION TO ENTER THE
BATTERY CELLS.
3. Use a wire brush with the baking soda solution
to properly clean the battery posts and
connctions.
4. Check battery connections for wear and loose
terminals. replace if necessary.
macHIne StoRaGe
1. Always store the machine indoors.
2. Always store the machine in a dry area.
3. Always store the machine in its upright position.
4. Always store the machine with the pad driver/
brush raised off the floor.
5. Always store the machine with the squeegee
assembly raised off the floor.
6. If storing in an area which may reach freezing
temperatures, be sure to drain all fluids from the
machine prior to storage. Any damage caused
by freezing temperatures will not be covered by
the warranty.
7. Drain the recovery tank.
8.
Drain the solution tank of all fluid.
Summary of Contents for i20NB
