background image

27

9. Error Type

Display

Error type

Causes

Action

Release

Operation

Evaporator 

temperature 

error

When the Evaporator temperature 
is 32 ℉ or more after 30 minutes 

passed during the ice making

Check refrigerant 

leakage

Check sensor and 

attachment abnormality

Resupply power 

after resolving 

cooling problem

Stop ice 

making

Evaporator 

temperature 

error

When the Evaporator temperature 

is over 23 ℉ after 30 minutes 

passed

Check refrigerant 

leakage

Check sensor and 

attachment abnormality

Resupply power 

after resolving 

cooling problem

Keep on ice 

making

Temperature 
sensor error 

Displayed when temperature 

sensor is open or shorted.

Check sensor and 

attachment abnormality

Start operation 

after sensor part 

repair

Stop ice 

making

High 

pressure 

switch error

Condenser dust, fan motor failure, 

cold cycle abnormality, etc.

Remove dust,

Check Fan motor 

Check for abnormal 

cold cycle

Automatic return 

after action

Stop 

compressor,

Stop 

motor after 

operating 10 

seconds.

High 

pressure 

switch error

Occurs when High pressure 

switch is OPEN 3 times or more

Contact service 

representative

Start operation 

after action

Stop 

compressor,

Stop 

motor after 

operating 10 

seconds.

Water supply 

error

When water level is not detected 

by the water level sensor due to 

no water supply for 120 seconds.

Water supply pressure 

check

Water level sensor 

check

Start operation 

after action

Stop ice 

making

Water level 

sensor defect

At the start of ice making, when 

the upper and lower limits are 

not detected by the water level 

sensor for 60 seconds

Replacement of Water 

Level Sensor

Start operation 

after action

Stop ice 

making

Motor 

restraint

Occurs when Evaporator inlet / 

outlet temperature is 3.2 ℉ or 

less for 2 minutes.

Poor water supply, Agitator 

restraint, Ice jams due to scale

Unlock ice jams

Check water supply 

line

Check motor restraint 

fault 

Start operation 

after action.

Machine stops 

after 3 repetitions

Stop ice 

making

① When Error occurs, the front use button (ICE-WATER-ICE & WATER) of the door lights alternately
    to the left and right. Restart after action. 
② When the button is lit alternately to the left and right, open the door and press the bottom setting 
    button of the control buttons, Error display will appear.

Summary of Contents for ID-0300-AN

































Reviews: