38
[ 4 - 2 4 ] S e n s i n g ( L e f t )
[ 4 - 2 4 ] S e n s i n g ( L e f t )
[ 4 - 2 5 ] W o r k i n g ( L e f t )
[ 4 - 2 5 ] W o r k i n g ( L e f t )
A g i t a t o r
A g i t a t o r
C l e a n i n g
C l e a n i n g
1 . C o n d i t i o n : C o . t i
2 . W o r k i n g T i m e : 1m i n
3 . D i s a s s e m b l e : 3 m i n
4 . W a r n n i n g W a s h : 7 d a y
5 . L o c k F r e e z e r : o f f
3 . B r e a k T i m e : 2 0 m i n
Do not turn off the power switch during the wash cycle.
This is because the program that detects washing is in operation
Explanation of the function buttons (set by an Administrator)
For your
information
[ 4 - 2 4 ] S e n s i n g ( L e f t )
C l e a n i n g
1 . W o r k i n g ? : O n
2 . S e n s i n g T i m e : 1 0 . 0 C
4-24-5: No wash lock setting
The product cannot be used when no washing is
performed within the days set for this category.
If this product cannot be used due to no washing,
perform cleaning according to the method indicated
in the manual.
4-25/4-25-1: Selecting the operation mode of the impeller
in the mix tank
The impeller in the mix tank operates depending
on the ON/OFF adjustment of the sensor of raw
material temperature in accordance with the
following items:
4-24-3:Dasher cover separation time setting during washing
This sets the separation time of the dasher cover during
washing. Be careful as a ‘wash failure’ is recorded when
the dasher cover is attached within the time set for this
category.
The time for this category means, the minimum time necessary to clean the parts inside the
cylinder such as the dasher, the blade, and so forth.
4-24-4: No wash warning date setting
An alarm(Voice Supported Model) is set off when washing is not performed within the value(days)
set within this category.
4-25-2: Operation maximum time setting
This is the function to limit the impeller operation time
by providing the maximum operation time under the
condition of impeller operation. It is usually used when a
lot of foam is created by raw material.
When the agitator operation time is short, ice may form on
the wall of the hopper.
4-25-3: Maximum rest time setting
The impeller stops when the raw material in the hopper reaches the set temperature,
and the impeller operates when the temperature reaches the operation temperature.
At this time, the temperature distribution in the hopper may not be even when it takes a
long time to reach the operation temperature.
Then setting the rest time for the agitator can control it.
4-24/4-24-1: Wash detection function setting
This is the category to select the wash detection
function.
4-24-2: Determine the temperature setting during washing
This adjusts the detection temperature in the cylinder and thehopper during washing when
‘4-24-1’ is activated.
“COMP” : Activated only when the compressor operates.
“ TIME ” : Operating in accordance with time
(4-25-2, 4-25-3)
setting independent from the operation of
the compressor
“ Co.t ” : Operating in the same way as the compressor, also activated by time setting (4-25)
after the materials in the reservoir bin reach the temperature setting.
Summary of Contents for ISIV-273SHC
