background image

 

 

1 INTRODUCTION 

 

Dear Customer, 
Thank you for having chosen our 

generator.

 

In your interests, we invite you to follow and observe the instructions in this manual to ensure the highest 
level of efficiency and duration of the unit. 

 

IMPORTANT: failure to observe the instructions in this manual will void the warranty conditions. 

 
 

2 SAFETY 

WARNINGS 

 

  

IMPORTANT 

For safety and for proper operation, carefully read this TECHNICAL MANUAL before installing and starting 
the generator. 
The manual is an integral and essential part of the generator and must accompany it from installation until 
disposal. The generator must be used for the purpose for which it was strictly intended and any liability by 
the Manufacturer for damages to people, animals or property due to lack of maintenance or for improper 
use, is excluded. 

 

  

Safety of the thermal power plant  

For safety purposes, the qualified technical personnel in charge of running the system must consider the following 
requirements: 

-

 

Follow the accident prevention and environmental safety regulations in force. 

-

 

Ensure the generator installation in the thermal power plant complies with the standards in force. 

-

 

Ensure that the electrical and hydraulic system complies with the standards in force. 

-

 

Ensure that the boiler room complies with the standards in force and is sufficiently ventilated. 

-

 

Ensure that the boiler fumes are conveyed outside the thermal power plant through a flue compliant with 
the standards in force. 

-

 

Ensure that the acidic condensation that may develop during system start-up, is evacuated outside the 
thermal power plant after a neutralisation process in compliance with the standards in force. 

-

 

Ensure that there is no danger due to frost inside the thermal power plant. 

 

  

System check 

Before switching on the generator for the first time, a duly qualified technician must perform a check at the central 
heating plant and update the system log once the check is over. 

 

 

Periodic verifications 

The generator must be periodically checked by a duly qualified technician (maintenance worker), who should up-
date the system log once the check is over. 

 

  

Danger of explosion 

Routine and extraordinary maintenance must be entrusted to 

professionally qualified personnel

 with the pur-

pose of promptly detecting any damage to the generator's pressurised body and the safety and control accesso-
ries. 

 

  

Danger deriving from the fuel 

Sensing the presence of fuel in the thermal power plant, it is appropriate to follow the precautions below to avoid 
the risk of explosions and fires: 

-

 

Do not smoke or cause sparks. 

-

 

Do not turn on lights or electrical devices in general (mobile phones). 

-

 

Open doors and windows. 

-

 

Close the fuel shut-off valve normally placed outside the thermal power plant. 

-

 

Disconnect the electrical power supply by using the switch normally placed outside the thermal power plant. 

Summary of Contents for CODEX





























Reviews: