background image

 

 

Engineering Manual for

 

 

 

 

AXS Series S40/S40i Keypad

 

 
 
 
 
S40/S40i Engineering Manual               

Page 8 of 8 

www.storm-interface.com

              

Rev 2.3 May  2016   

                                 © Copyright Storm Interface. 2015. All rights reserved

 

 

Regulatory Information 
 

This device complies with Part 15 of the FCC Rules and Industry Canada licence exempt RSS standard(s). 
Operation is subject to the following two conditions: 
1. This device may not cause interference, and 
2. This device must accept any interference, including interference that may cause 
undesired operation of the device. 
 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. 
L'exploitation est autorisée aux deux conditions suivantes :  
(1) l'appareil ne doit pas produire de brouillage, et  
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible 
d'en compromettre le fonctionnement. 

 
 

 
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur 
 
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 
 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
—Consult the dealer or an experienced radio/TV technician for help. 
 
Changes or modifications not expressly approved by the party responsible for compliance could void the user's 
authority to operate the equipment 

 

 
 

Summary of Contents for AXS S40









Reviews: