11
OTHER FUNCTIONS
45
Repeater tone
D
Select the subaudible tone needed to access the re-
peater. A total of 50 tone frequencies (67.0–254.1 Hz)
are selectable. (default: 88.5 Hz)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Tone squelch frequency
D
Select the CTCSS tone frequency to use for the Tone
Squelch function.
A total of 50 tone frequencies (67.0–254.1 Hz) are se-
lectable. (default: 88.5 Hz)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
• Selectable subaudible tone frequencies
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
DTCS code
D
Set the DTCS code (both encoder and decoder) for
DTCS squelch operation. A total of 104 codes are se-
lectable. (default: 023)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
DTCS polarity
D
Set
the Transmit and Receive DTCS polarity to “NN,”
“NR,” “RN” or “RR.” (default: NN)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Frequency offset
D
Set the duplex frequency offset between 0 and 20 MHz.
In the duplex mode, the transmit frequency shifts up or
down from the receive frequency by the offset amount.
(default: Depending on the transceiver versions)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Reverse function
D
Turn the Reverse Duplex function ON or OFF (default).
When the Reverse Duplex function is ON, the receive
and transmit frequencies are reversed.
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
OFF: Normal duplex (default)
ON: Reversed duplex
Tuning step
D
Set the VFO tuning step to 5, 6.25, 10, 12.5, 15, 20, 25,
30 or 50 kHz. (default: Depending on the versions)
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Scan pause timer
D
Select the scan pause timer option.
When receiving a signal, the scan pauses according to
the scan Pause Timer. (default: SCP-10)
• “SCP-2”–“SCP-20” : When receiving a signal, the
scan pauses for 2 to 20 seconds
(set in 2 seconds steps).
• “SCP-HO”
: When a signal is received, the
scan pauses until it disappears.
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Scan resume timer
D
Set the scan resume options of a pause after the re-
ceived signal disappears. (default: SCT-2)
• “SCT-0”
: The scan resumes immediately
after the signal disappears.
• “SCT-1”–“SCT-5”
: The scan resumes 1 to 5 seconds
after the signal disappears.
• “SCT-HO”
: The scan remains paused ac-
cording to the Pause Timer, even
if the signal disappears. Rotate
[DIAL]
to resume the scan.
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Display dimmer
D
Set the backlight brightness to between 1 (Dark) and
4 (Bright; default).
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
Auto dimmer
D
Set the Auto Dimmer brightness.
The Auto Dimmer function automatically reduces the
backlight brightness if no operation has been performed
for 5 seconds.
• “ATD OF” (default) : Auto Dimmer function is turned OFF.
The backlight is continuously ON,
while the transceiver is turned ON.
• “AT OF”
: The backlight automatically turns
OFF if no operation has been per-
formed for 5 seconds.
• “AT D1” – “AT D3” : The backlight lights with the level 1
(Dark) to 3 (Bright), if no operation
has been performed for 5 seconds.
LOCK
SET
ANM
MONI
DUP
LOW
T-SCAN
TONE
PRIO
M/CALL
SCAN
V/ MHz
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
