background image

2-1

INSTALLATION AND CONNECTIONS

                  IC-7700

Unpacking ……………………………………………………………… 2-2

Main dial attachment  …………………………………………………… 2-2

Rack mounting handle detachment …………………………………… 2-3

Selecting a location  …………………………………………………… 2-3

Grounding ……………………………………………………………… 2-4

Antenna connection  …………………………………………………… 2-4

USB-Memory connection  ……………………………………………… 2-4

Required connections  ………………………………………………… 2-5

D

Front panel  …………………………………………………………… 2-5

D

Rear panel  …………………………………………………………… 2-5

Advanced connections  ………………………………………………… 2-6

D

Front panel  …………………………………………………………… 2-6

D

Rear panel—1 

……………………………………………………… 2-6

D

Rear panel—2 

……………………………………………………… 2-7

Linear amplifier connections …………………………………………… 2-8

D

Connecting the IC-PW1/EURO  …………………………………… 2-8

D

Connecting a non-Icom linear amplifier  …………………………… 2-8

Transverter jack information  …………………………………………… 2-9

FSK and AFSK (SSTV) connections  ………………………………… 2-9

Microphone connector information  ………………………………… 2-10

Microphones (options) ………………………………………………… 2-10

D

SM-20 ……………………………………………………………… 2-10

D

HM-36 ……………………………………………………………… 2-10

Accessory connector information  …………………………………… 2-11

CAUTION!: The transceiver weighs approx. 24 kg (53 lb).

Always have two people available to carry, lift or
turn over the transceiver.

Summary of Contents for IC-7700












Reviews: