background image

*See engineers notes at rear

  

 

Page 

9 Guarantee 

 

Thank you for purchasing one of our amplifiers. We 
trust you will be pleased with it.  
 

This amplifier is guaranteed by the dealer you 
purchased from for 12 months from the date of 
purchase for parts and labour, excluding 
shipping. Valves are consumables and therefore 
on a 12 months pro-rata wear basis. Please keep 
your receipt as proof of purchase, this will be 
needed.  

 
All units are individually tested for performance for at 
least ten hours before despatch to you. In the unlikely 
event that you believe the unit is not functioning 
correctly, it may be helpful to contact us first as we 
may be able to assist you. Then we would request 
that you return the item to your dealer. 
 
You are advised to inform us of any change of 
address or change of ownership in order that we may 
keep you up to date of any upgrades or 
improvements. Check our website. 
 

Exclusions 

Claims for any damage to either amplifiers or valves 
must be reported within 24 hours of receipt. 
 
This amplifier is designed for normal domestic hi fi 
use. It is not guaranteed for commercial, Public 
Address use, or use in other situations. The 

guarantee becomes void if the unit has been 
modified in any way not approved by Icon Audio. 
 

10 Packing Instructions 

It is essential that the original box and packing be 
kept in good condition, as this provides vital 
protection from damage during transit. Please do 
not write on box, but use removable labels. 

Should the original box and packaging be lost or 
become unusable a repacking charge of one hundred 
pounds will be made.  

  Re-use the supplied plastic bag to keep the 

amp clean and free from damp. 

  The mains lead fits in a foam cut-out 

underneath the amplifier. 

 

Send the valve covers and valves in the 
separate supplied box. See above for 
valve removal. 

  Valves should be removed, numbered and 

packed in “Bubblewrap” or similar for 
protection inside the valve cover.  

  If the amplifier is stored in the box, keep 

upright. 

  Do not store in damp conditions as the 

transformer windings will corrode. 

  If the amplifiers are shipped insurance is 

desirable due to the high unit value. 

 

 

icon 

Audio

 

UK LTD

 

351 Aylestone Road Leicester  LE2 8TA 

www.iconaudio.co.uk 

Phone +44 (0) 116 244 0593  

Cell +44 (0) 778 715 8791 

Email: sales@iconaudio.com 

2014-08-28 G version 

 
 

 

 

Summary of Contents for MB30m











Reviews: