background image

22

 HOW TO FOLD THE TREADMILL

To avoid damaging the treadmill, adjust the incline 

to the lowest position before you fold the treadmill. 

Then, remove the key and unplug the power cord. 

CAUTION: You must be able to safely lift 45 lbs. (20 

kg) to raise, lower, or move the treadmill.   

1.    Hold the metal frame firmly in the location shown 

by the arrow below. CAUTION: Do not hold the 

frame by the plastic foot rails. Bend your legs 

and keep your back straight.   

2.    Raise the frame until the latch knob locks in the 

storage position. CAUTION: Make sure that the 

latch knob locks.

  

To protect the floor or carpet, place a mat under the 

treadmill. Keep the treadmill out of direct sunlight. 

Do not leave the treadmill in the storage position in 

temperatures above 85° F (30° C).

HOW TO MOVE THE TREADMILL 

 Before moving the treadmill, fold it as described at the 

left. CAUTION: Make sure that the latch knob is 

locked in the storage position. Moving the treadmill 

may require two people.

1.    Hold the frame and one of the handrails, and place 

one foot against a wheel. 

2.     Pull back on the handrail until the treadmill will roll 

on the wheels, and carefully move it to the desired 

location. CAUTION: Do not move the treadmill 

without tipping it back, do not pull on the frame, 

and do not move the treadmill over an uneven 

surface.

3.    Place one foot against a wheel, and carefully lower 

the treadmill.

HOW TO LOWER THE TREADMILL FOR USE

1.  

See drawing 2. Hold the upper end of the treadmill 

with your right hand. Then, pull the latch knob to 

the left and hold it. IMPORTANT: Do not turn the 

latch knob. If necessary, push the frame forward 

slightly. Pivot the frame downward a few inches, 

and release the latch knob. 

2.  

See drawing 1 at the left. Hold the metal frame 

firmly with both hands, and lower it to the floor. 

CAUTION: Do not hold the frame by the plastic 

foot rails, and do not drop the frame. Bend your 

legs and keep your back straight. 

 HOW TO FOLD AND MOVE THE TREADMILL 

Latch 

Knob

2

Frame

Frame

1

Handrail

Frame

Wheel

1

Summary of Contents for PRO-FORM 700 LT

































Reviews: