background image

19

HOW TO PLAY THE CALORIE DESTROYER GAME

The Calorie Destroyer game is a fast-paced game that

pits you against a squadron of laser-firing drones. In

addition to the console buttons, you will use the four-

button game controllers on the handlebar to play the

game. Follow the steps below to play the Calorie

Destroyer game.

1. Begin pedaling or press any button on the

console to turn on the console.

When you turn on the console, the display will turn

on. The console will then be ready for use.

2. Select the Calorie Destroyer game.

To select the Calorie Destroyer game, press the

Calorie Destroyers button (see the drawing on

page 14).

3. Press a button on either controller to start the

game.

When you start the Calorie Destroyer game, a

game arena will appear in the display. Three rows

of drones will begin to move across the top of the

arena, periodically firing their lasers downward.

Each time the drones reach the left or right side of

the arena, they will reverse direction and move

downward.

At the bottom of the arena is a laser blaster. You

can fire the laser blaster at the drones by pressing

the up button on either controller. In addition, while

you are pedaling, you can move the laser blaster

to the left or right using the left and right buttons

on either controller. The faster you pedal, the

faster the laser blaster will move.

Between the drones and the laser blaster are five

shields. You can hide the laser blaster below a

shield if desired. However, each time a shield is hit

by a laser, a piece will be vaporized.

Your goal is to keep the laser blaster from being

hit and to keep any drone from reaching the bot-

tom of the arena. If the laser blaster is hit, it will be

disabled and another laser blaster will appear in its

place; there are a total of four laser blasters. If you

vaporize the entire squadron of drones, a new

squadron will appear.

As you play, the drones will move faster and

faster. The game will continue until all four laser

blasters are disabled or a drone reaches the bot-

tom of the arena.

When the game ends, the display will show the

level of play that you reached and your final score.

The display will then show the four highest scores

recorded since the scores were reset. If desired,

press and hold down the right button on either

controller to reset the scores. Note: If your score is

one of the four highest, the display will prompt you

to enter a name consisting of three letters or dig-

its. While the line below the first letter is flashing,

press the up and down buttons on either controller

to select the desired letter or digit. Next, press the

right button on either controller and select another

letter or digit. Repeat this process to select a third

letter or digit. Then, press the right button on either

controller again. The display will then show the

four highest scores recorded since the scores

were reset.

4. Follow your progress with the display.

While you exercise and play the Calorie Destroyer

game, the upper left corner of the display will

show the elapsed time. In addition, the display will

show the game level that you have reached and

your current score.

To pause the game, press the Display button. To

resume the game, press the Display button

repeatedly until the word DESTROYER appears at

the top of the display, and then press a button on

either controller.

5. When you are finished exercising, the console

will turn off automatically.

See step 6 on page 16.

Summary of Contents for NordicTrack GX2





























Reviews: