background image

22

HOW TO USE THE INFORMATION MODE

1. Press and hold down the TV button and adjust

the television settings if desired.

Press and hold down the TV button for several
seconds to access the information mode. The
brightness level indicator will appear on the televi-
sion screen. Press the Volume buttons to adjust
the brightness setting if desired.

Next, press the Channel buttons until the contrast,
color, sharpness, or hue level indicator appears.
Adjust the settings, if desired, by pressing the
Volume buttons.

Note: The elliptical exerciser features a demo
mode that is intended to be used only while the
elliptical exerciser is displayed in a store. When
the demo mode is turned on, the console will 

not

turn off automatically when the elliptical exerciser
is not in use. Press the Start button repeatedly to
turn off or turn on the demo mode. The words
DEMO OFF or DEMO ON will appear at the top of
the screen to indicate whether the mode is turned
on or off.

2. Press the TV button again and add or delete

channels.

Note: Complete this step only if you are using ana-
log cable.

After all valid channels available in your area have
been saved into the television’s memory (see step
4 on this page), you can manually add channels or
delete unwanted channels.

To add or delete a channel, first press the Channel
buttons until the desired channel number appears
on the screen. Then, press the Volume increase
button to add the channel, or the Volume decrease
button to delete the channel. Continue this

process until you have added all desired channels
and deleted all unwanted channels.

3. Press the TV button again and select a cable

connection. 

After you press the TV button, press the Volume
increase button to select the Standard Cable set-
ting, the Channel decrease button to select the
Cable IRC setting, or the Channel increase button
to select the Cable HRC setting. Note: If you have
connected a CATV cable, one of the three Cable
settings should be selected; try all three Cable set-
tings, if necessary, to find the optimal setting. 

4. Press the TV button again and save channels

into the television’s memory. 

When you press the TV button, the television will
begin scanning all the channels available in your
area. When no broadcast signal is detected on a
channel, the channel will be skipped. When a
cable signal is detected, the channel will be saved
into memory and the next channel will be selected.
This process will continue until the highest channel
number is reached. 

Do not exit the information

mode while the television is scanning for chan-
nels. 

Note: If you are viewing channels through an

external source such as a cable box or a VCR, the
television will save only the channel used by the
external source.

5. When you are finished using the information

mode, press the Display button.

To exit the information mode at any time (except
while the television is scanning channels), press
the Display button.

Summary of Contents for PRO-FORM Perspective 1000

































Reviews: