background image

iControl Incorporated 
http://www.iControl-Inc.com 

NCC 

 

減少電磁波影響,請妥適使用

  

(For Reducing RF Influence, Use Properly)

  

 

為維護隱私權,請妥適使用

  

(For protect individual privacy, Use Properly)

  

 

本器材須經專業工程人員安裝及設定,始得設置使用,且不得直接販售給一般消費者。

  

(This device must be installed by expert and will not be sold directly to the general public through retail

  

store)

  

 
 

低功率電波輻射性電機管理辦法

  

第十二條

 

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變
更原設計之特性及功能。

  

第十四條

 

低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至
無干擾時方得繼續使用。

   

  

                  

前項合法通信,指依電信法規定作業之無線電通信。

   

  

                  

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

  

 

WARNING

  

Administrative Regulations on Low Power Radio Waves Radiated Devices warning:

  

Article 12

  

Without permission granted by the NCC, any company, enterprise, or user is not

  

allowed to change frequency, enhance transmitting power or alter original

  

characteristic as well as performance to an approved low power radio

frequency

  

devices.

  

Article 14

  

The low power radio

frequency devices shall not influence aircraft security and

  

interfere legal communications; If found, the user shall cease operating immediately

  

until no interference is achieved.

  

The said legal communications means radio communications is operated in

  

compliance with the Telecommunications Act.

  

The low power radio

frequency devices must be susceptible with the

  

interference from legal communications or ISM radio wave radiated devices.

 

 

 

Summary of Contents for iscan











Reviews: