20
PDX-08
PDX-08
PDX-08
PDX-089
9
9
9T
T
T
T
DM&P
Vortex
86DX
™
Panel PC with 8.9” WSVGA TFT LCD
3.1
3.1
3.1
3.1....
P
P
P
PD
D
D
DX-089
X-089
X-089
X-089T
T
T
T Devel
Devel
Devel
Develo
o
o
op
p
p
pmen
men
men
mentttt Note
Note
Note
Note
<Pri
<Pri
<Pri
<Prim
m
m
maaaarrrryyyy ////Se
Se
Se
Secccconda
onda
onda
ondarrrryyyy IIIID
D
D
DE
E
E
E:::: Ma
Ma
Ma
Masssste
te
te
terrrr o
o
o
orrrr S
S
S
Sllllaaaave>
ve>
ve>
ve>
Micro SD: Primary Master
CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of CF
slot) to adjust Master or Slave
<Wind
<Wind
<Wind
<Windo
o
o
ow
w
w
w C
C
C
CE
E
E
E6.
6.
6.
6.0000 developmen
developmen
developmen
developmentttt g
g
g
gu
u
u
uiiiid
d
d
deeee>
>>>
Windows Embedded CE 6.0 BSP, trial CE image and development notes, please visit
Vortex86DX CPU website to get more information:
http://www.dmp.com.tw/tech/vortex86dx/
<
<<<L
L
L
Lin
in
in
inu
u
u
uxxxx iiiin
n
n
nssssttttalla
alla
alla
allattttiiiio
o
o
on
n
n
n no
no
no
notttteeee>
>>>
Please forced the IDE setting in BIOS to PIO mode before install Linux
on PDX-089T as follows:
1-Go to the advanced BIOS setting and make the “Onboard IDE Operate Mode” is
““““Legac
Legac
Legac
Legacyyyy M
M
M
Mode
ode
ode
ode””””
2-Go to the PCI/PnP and make the “PCI IDE BusMaster” is
““““Disable"
Disable"
Disable"
Disable"
<
<<< X
X
X
XP
P
P
P p
p
p
prrrrofessi
ofessi
ofessi
ofessio
o
o
on
n
n
naaaallll /Hom
/Hom
/Hom
/Homeeee /E
/E
/E
/Emb
mb
mb
mbed
ed
ed
edd
d
d
deeeed
d
d
d an
an
an
and
d
d
d Win
Win
Win
Wind
d
d
do
o
o
ow
w
w
wssss 200
200
200
2000000 iiiin
n
n
nssssttttallatio
allatio
allatio
allation
n
n
n n
n
n
no
o
o
otttteeee >
>>>
1-Please visit Vortex86DX CPU website to get more information:
http://www.dmp.com.tw/tech/vortex86dx/
2-Go to the Advanced and make "Onboard IDE operate Mode"
""""N
N
N
Nativ
ativ
ativ
ativeeee mode"
mode"
mode"
mode"
3-If your CF Card support UDMA2/4, please Go to the PCI PnP and make the “PCI
IDE BusMaster” is
““““E
E
E
En
n
n
naaaab
b
b
blllleeee””””
<Enhanc
<Enhanc
<Enhanc
<Enhanceeee C
C
C
CF
F
F
F tttto
o
o
o ru
ru
ru
run
n
n
n th
th
th
theeee U
U
U
UD
D
D
DMA2/4>
MA2/4>
MA2/4>
MA2/4>
1-Make sure the CF Card is supporting UDMA 2/4 Mode or not.
2-Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Enable”
<Ho
<Ho
<Ho
<How
w
w
w tttto
o
o
o b
b
b
boo
oo
oo
ootttt u
u
u
up
p
p
p ffffro
ro
ro
rom
m
m
m tttth
h
h
heeee Mic
Mic
Mic
Micrrrro
o
o
o S
S
S
SD
D
D
D ca
ca
ca
carrrrd
d
d
d>
>>>
1-Get into the BIOS setup Utility
2-Go to the Advanced
3-Choose Primary IDE Pin Select: SD card
4-Press “F10” to save configuration changes and exit setup
