M-7026
M-7026 User Manual Rev: 1.5 Date: 2016/03/10
124
2.60 @AADACi
Description:
This command is used to disable the high and low alarms for a specific Analog
Input channel of a specified module.
Syntax:
@AADACi[CHKSUM](CR)
@
Delimiter character
AA
The address of the module to be set in hexadecimal format (00 to FF)
DA
The command to disable the high and low alarms for the Analog Input
channel
Ci
The Analog Input channel where the alarms are to be disabled, zero
based
(0-5)
Response:
Valid Command:
!AA[CHKSUM](CR)
Invalid Command:
?AA[CHKSUM](CR)
!
Delimiter character to indicate a valid command
?
Delimiter character to indicate an invalid command
AA
The address of the responding module in hexadecimal format (00 to
FF)
There will be no response if the command syntax is incorrect, there is a
communication error, or there is no module with the specified address.
Examples:
Command: @01RAC0
Response: !011
Reads the Alarm Type for Analog Input channel 0 of module 01 and
returns a response indicating that the command was successful and that
the Alarm Type is Momentary.
Command: @01DAC0
Response: !01
Disables the high and low alarms for Analog Input channel 0 of module 01
and returns a response indicating that the command was successful.
Command: @01RAC0
Response: !010
Reads the Alarm Type for Analog Input channel 0 of module 01 and
returns a response indicating that the command was successful and that
the alarm is disabled.
Command: @01DACF
Response: ?01
Attempts to disable the high and low alarms for Analog Input channel 15
of module 01 and returns an response indicating that the command was
unsuccessful because Analog Input channel 15 does not exist.
Related Commands:
Section 2.55 @AACHCi, Section 2.58 @AACLCi, Section 2.61 @AADI,
Summary of Contents for M-7026
