M-7026 User Manual Rev: 1.5 Date: 2016/03/10
16
1.8.2 Analog Output
The Analog Output calibration procedure is as follows:
1.
Warm up the module for 30 minutes.
2.
Set the Type Code to the type you wish to calibrate. Refer to
Section 2.23 for details.
3.
Enable calibration. Refer to Section 2.47 for details.
4.
Set the zero Analog Output voltage/current. Refer to Section 2.5
for details.
5.
Check the meter and trim the output until zero output is achieved.
Refer to Section 2.11 for details.
6.
Send the Analog Output Zero Calibration command. Refer to
Section 2.7 for details.
7.
Set the span Analog Output voltage/current. Refer to Section 2.5
for details.
8.
Check the meter and trim the output until the span output is
achieved. Refer to Section 2.11 for details.
9.
Send the Analog Output Span Calibration command. Refer to
Section 2.9 for details.
Notes:
1.
For Analog Output channels, calibration must be performed for
each channel individually, so the calibration voltage/current
source should be connected to the specific channel that is to be
calibrated.
2.
When calibrating Types Codes 0 and 1, the jumper for the
corresponding channel
should be set to the “current input”
position.
3.
Calibration voltages and currents are shown below.
Calibration Voltages/Current:
Type Code
0
1
2
3
4
5
Zero Output
0 mA
4 mA
0 V
0 V
0 V
0 V
Span Output
+20 mA
+20 mA
+10 V
+10 V
+5 V
+5 V
Summary of Contents for M-7026
