ICP N9MSB Service And Technical Support Manual Download

Page: 20 / 30

SERVICE AND TECHNICAL SUPPORT MANUAL

Gas Furnace: N9MSB

Specifications subject to change without notice.

440 04 4413 03

18. Check igniter resistance. Nominal resistance is 40 to 70

ohms at room temperature and is stable over the life of

the igniter.

19. Clean burner with a brush and a vacuum.
20. Clean the flame sensor with fine steel wool (0000 grade).

Do not use sand paper or emery cloth.

Figure 9

Burner Assembly

URNER

SSY

LAME

ENSOR

(

ELOW

URNER)

LAME

OLL

−

OUT

WITCH

URNER

UPT.

SSY

L11F064

Representative drawing only, some models may vary in appearance.

To reinstall burner assembly:

1. Install the Hot Surface Igniter (HSI) and bracket in burner

assembly.

2. Install flame sensor on burner.
3. Align the edges of the one-piece burner with the slots in

the burner assembly and slide the burners forward until

they are fully seated in the burner assembly.

4. Align the orifices in the manifold assembly with the

support rings on the end of the burner.

5. Insert the orifices in the support rings of the burners.

NOTE

: If manifold does not fit flush against the burner, do not

force the manifold on the burner assembly. The burners are not
fully seated forward in the burner assembly. Remove the

manifold and check burner positioning in the burner assembly
assembly before re-installing the manifold.

6. Attach the green/yellow wire and ground terminal to one

of the manifold mounting screws.

7. Install the remaining manifold mounting screws.
8. Check the igniter alignment. See

Figure 9

Figure 10

and

Figure 11

Figure 10

Igniter Position

−

Top View

A11405

2-1/2-in.

(64.4)

1-1/4-in.

(31.8)

Figure 11

Igniter Position

−

Side View

L12F041

in.

2.5 mm

3/8

in.

3/16

in.

+0.8

1.5 mm

50 mm

9.6 mm

4.6 mm

1/10

in.

+ 1/32

1/16

in.

9. Attach the wires to the roll-out switches.

10. Align the burner assembly with the openings in the

primary cell inlet panel and attach the burner assembly to

the cell panel.

11. Connect the wire for the flame sensor.

12. Connect the wire for the Hot Surface Igniter.

NOTE

: Use propane-resistant pipe dope to prevent leaks. Do

not use Teflon tape.

13. Install the gas pipe to the gas valve.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow this warning could result in personal injury,

death, and/or property damage.
Never purge a gas line into a combustion chamber. Never

test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for the detection of

leaks to check all connections. A fire or explosion may result

causing property damage, personal injury or loss of life.

14. Check for gas leaks with a commercially available soap

solution made specifically for the detection of leaks.

15. Turn gas on at electric switch on gas valve and at

external shut-off or meter

16. Turn power on at external disconnect, fuse or circuit

breaker.

17. Run the furnace through two complete heating cycles to

check for proper operation

18. Install control door when complete.

Servicing Hot Surface Igniter

The igniter does

NOT

require annual inspection. Check igniter

resistance before removal. Refer to

Figure 9

Figure 10

and

Figure 11

1. Turn off gas and electrical supplies to furnace.
2. Remove control door.
3. Disconnect igniter wire connection.

Summary of Contents for N9MSB































Search results

Summary of Contents for N9MSB

Reviews:

Related manuals for N9MSB

Brands by name

Popular brands

ICP N9MSB, Service And Technical Support Manual

Search results

Summary of Contents for N9MSB

Reviews:

Related manuals for N9MSB

Brands by name

Popular brands