ICP N9MSB Service And Technical Support Manual Download | Manualshive

Page: 29 / 30

background image

SERVICE AND TECHNICAL SUPPORT MANUAL

Gas Furnace: N9MSB

Specifications subject to change without notice.

440 04 4413 03

29

PARTS REPLACEMENT INFORMATION GUIDE

Casing Group

Control door
Blower door
Top filler plate
Bottom filler plate
Door knob assembly

Electrical Group

Control box
Junction box
Limit switch(es)
Circuit board
Door switch
Transformer
3

−

Amp fuse

Flame rollout switch
Main wiring harness
Blower motor harness (when used)

Filter Group

Filter(s)

Blower Group

Cut

−

off plate

Blower housing
Blower motor
Blower wheel
Capacitor (when used)
Capacitor strap (when used)
Power choke (where used)

Gas Control Group

Manifold
Burner
Orifice
Flame sensor
Hot surface igniter
Gas valve

Heat Exchanger Group

Primary Heat Exchanger assembly
Primary Heat Exchanger cell panel
Secondary Heat Exchanger assembly
Coupling box
Containment plate
Tubing gaskets

Inducer Group

Pressure switch(es)
Inducer assembly
Inducer
Inducer motor
Motor module (when used)
Inducer motor capacitor (when used)
Collector box
Condensate trap
Condensate trap elbow
Gaskets

!

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK AND CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in dangerous operation, personal injury, death or property damage.
Improper installation, adjustment, alteration, service, maintenance, or use can cause carbon monoxide poisoning, explosion, fire,

electrical shock, or other conditions which may cause personal injury or property damage. Consult a qualified installer, service

agency, local gas supplier, or your distributor or branch for information or assistance. The qualified installer or agency must use only

factory-authorized and listed kits or accessories when modifying this product.

Have available the product/model number and the serial number located on the unit rating plate to ensure correct replacement parts.
TO OBTAIN INFORMATION ON PARTS: Consult your installing dealer or the classified section of your local telephone directory

under the “Heating Equipment“ or “Air Conditioning Contractors and Systems” headings for dealer listing by brand name.

International Comfort Products

Consumer Relations Department

P.O. Box 128

Lewisburg, TN 37091, USA

931

−

270

−

4100

«
...
27
28
29
30
»

Summary of Contents for N9MSB































Reviews:

No comments

Related manuals for N9MSB

Brand: WaterFurnace Pages: 38

Brand: barbas Pages: 32

Brand: Empyre Pages: 30

Brand: FURNACE & ASSAY Pages: 17

CARBOLITE GERO HST 12/400

Brand: VERDER Pages: 30

CARBOLITE GERO KZS 12/600

Brand: VERDER Pages: 32

CARBOLITE GERO GSM 11/8

Brand: VERDER Pages: 34

CARBOLITE GERO G Series

Brand: VERDER Pages: 46

CARBOLITE GERO EVA 12/150B

Brand: VERDER Pages: 56

Brand: Lennox Pages: 52

Brand: KDF Pages: 19

(T,G)G9S040A08MP11

Brand: Johnson Controls Unitary Products Pages: 2

Brand: York Pages: 24

Brand: Whirlpool Pages: 32

Brand: Trane Pages: 24

Brand: Trane Pages: 39

Brand: International comfort products Pages: 56

Brand: Maytag Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands