background image

10

Chapter 2: Bluetooth Settings

Pairing with an iPhone

To use an iPhone with your Bluetooth handset, you must
first pair and connect the iPhone with the handset.

Make sure the handset is power off before starting the
pairing process, and place the Bluetooth handset within
1 meter away from your iPhone.

Turn on the Bluetooth feature of your iPhone. Click

,

,

and

, then the

iPhone searches for available devices.

Press and hold

MFB for about 6 seconds until the

red and blue indicator flash alternately.

When the iPhone finds

, click

to

connect it with the base. The iPhone prompts you to
enter the PIN (the default PIN is 0000). Enter it, then
click

to confirm. When the iPhone is successfully

connected,

displays, and the handset blue

indicator flashes, 1 second on and then 3 seconds off.

Settings

General

Bluetooth

OFF

i-400

Not Paired

Pair

Connected

1

2

3

4

11

Connecting an iPhone

Although two iPhones can be paired with the BT handset,
only one iPhone can be connected to the base and be
engaged in a call at one time.

The BT handset will connect to the last paired iPhone
automatically when the handset is switched off then on,
and within 10 meters range. Ensure the Bluetooth feature
is enabled on the iPhone.

If you switch off the Bluetooth feature on the iPhone and
then switch it on, you should connect it again. Click

to the right side of

on the iPhone screen.

After the connection is successful,

appears.

Not

Connected

i-400

Connected

Notes:

Make sure the handset and the iPhone are no more
than a meter apart, so they are within operable range.
If the handset is not successfully paired within 2
minutes, after a long beep, it will automatically leave
pairing mode. If you still want to pair, please repeat the
steps of pairing again.

Note:

To pair a new iPhone, remember to turn the Bluetooth
handset off and then turn it on again.

Summary of Contents for i-400













Reviews: