background image

Chapter X: XXXXX

Page 1

            ADDENDUM

  IRQGEN.VXD  and  Win32IRQ.DLL

IRQGEN.VXD

Description

IRQGEN.VXD is a Virtual Device Driver, or VxD, for Windows95. Together with
Win32IRQ.DLL, it allows a program to easily respond to hardware interrupt requests, or IRQs.

Installation

To install IRQGEN.VXD, copy it to C:\Windows\System. If your hard drive has a letter other than
C, substitute the appropriate letter. It is not necessary to reboot your system prior to using
IRQGEN.VXD.

Win32IRQ.DLL

Description

Win32IRQ.DLL is a Dynamic Link Library, of DLL, for Windows95. It provides a simple interface
to IRQGEN.VXD, allowing a program to easily respond to hardware interrupts. Three functions are
exported by Win32IRQ.DLL: InitIRQ,, Detect IRQ, and SendEOI. To use these functions in a
program, they must first be inported. In Pascal, the necessary lines would be:

function InitIRQ (MyIRQ:  Byte) : Boolean; stdcall;external 'Win32IRQ.dll'

index 1;

function DetectIRQ:  Boolean; stdcall; external "Win32IRQ.dll"index 2;

function SendEOI:  Boolean; stdcall; external "Win32IRQ.dll" index 3;

In C, the library file Win32IRQ.lib must first be linked to the program. This is accomplished by
adding it to the project or editing the makefile. The following lines would then create the prototypes
for the DLL functions:

extern "c" _declspec (dllimport) bool pascal InitIRQ (unsigned char MyIRQ);

extern "c" _declspec (dllimport) bool pascal DetectIRQ (void);

extern "c" _declspec (dllimport) bool pascal SendEOI (void) ;

InitIRQ

This function performs the initialization required to detect IRQs. It must be called before
DetectIRQand SendEOI can be called, although calling those functions first will only cause them to
return a value of FALSE. The function's sole parameter is an unsigned 8-bit value containing the
IRQ number to monitor. The return result is TRUE if initialization was compledted successfully,
FALSE if not.

Addendum: 00650-010-6B
© 1998, Industrial Computer Source, 6260 Sequence Drive,  San Diego, CA 92121-2720. All rights reserved.

Summary of Contents for AOB8/16









































Reviews: