background image

Auto Sentry® Petro - Installation Guide

9

Site Layout

Auto Sentry® Petro In-bay Layout

Figure 1. Auto Sentry® Petro In-bay Layout

6"

FINISHED TRAFFIC GRADE 

LINE

Auto Sentry Petro

RAISED            CURB

BOLLARD

SEE NOTE

Minimally 12 Feet

AUTO SENTRY

®  

PETRO 

IN-BAY LAYOUT

***  THIS DRAWING IS ONLY INTENDED TO SHOW THE GENERAL LAYOUT AND DIMENSIONS 

NECESSARY FOR THE PROPER PLACEMENT OF THE AUTO SENTRY PETRO.  ANY DEVIATION 

MAY CAUSE DAMAGE TO THE AUTO SENTRY PETRO.  ***

THE HEIGHT  FROM THE BOTTOM OF THE AUTO 

SENTRY TO THE BOTTOM OF ANY CANOPY WILL 

BE DETERMINED BY THE CAR WASH, BUT 

SHOULD BE ONLY SLIGHTLY GREATER THAN THE 

MAXIMUM ALLOWABLE HEIGHT FOR ANY 

VEHICLE TO ENTER THE IN-BAY .

CANOPY ABOVE AUTO SENTRY PETRO

NOTE:

  ICS DOES NOT RECOMMEND AN IDEAL DISTANCE BETWEEN THE 

AUTO SENTRY PETRO AND THE ENTRANCE TO THE IN-BAY TUNNEL, BUT 

DOES OFFER THE FOLLOWING INFORMATION TO THE IN-BAY OWNER FOR 

THEM TO DECIDE WHAT THE APPROPRIATE DISTANCE SHOULD BE FOR 

THEIR SITE:

1. THE

 TYPE OF IN-BAY AUTOMATIC

:  EACH IN-BAY AUTOMATIC IS 

DIFFERENT AND THEY ALL EXPEL DIFFERENT AMOUNTS OF BOTH WATER 

AND CHEMICALS, WHICH IF BLOWN ONTO THE AUTO SENTRY PETRO IN 

ANY GREAT AMOUNT COULD IMPEDE THE USERS ABILITY TO SEE AND/OR 

PROPERLY UTILIZE THE TOUCH SCREEN.

2. THE 

RELATIVE WIND DIRECTION

:  IF THE PREVAILING WIND BLOWS 

FROM THE AUTO SENTRY PETRO TO THE BAY ENTRANCE, THEN THERE 

SHOULD BE ONLY MINOR PROBLEMS FROM BLOW-BACK.  IF THE 

PREVAILING WIND BLOWS THROUGH THE BAY TOWARDS THE AUTO 

SENTRY PETRO THEN THE AUTO SENTRY PETRO WILL BE GREATLY 

AFFECTED.  IF THE PREVAILING WIND IS PERPENDICULAR TO THE TUNNEL 

THERE WILL AGAIN BE MINOR PROBLEMS.

3.

DRYER TYPE: 

 THE TYPE OF DRYER USED IN THE WASH WILL ALSO BE A 

FACTOR.  DRYERS THAT SIMPLY BLOW  DOWN THE TUNNEL TOWARDS 

THE AUTO SENTRY PETRO WILL FACILITATE THE BUILDUP OF WATER AND 

CHEMICALS ON THE AUTO SENTRY PETRO EVEN ON WINDLESS DAYS. 

4.

BAY DOORS

:  IF BAY DOORS ARE INSTALLED AND CLOSE BETWEEN 

VEHICLES, THEN THERE SHOULD NOT BE ANY PROBLEMS AT ALL AND THE 

AUTO SENTRY PETRO CAN BE PLACED AS CLOSE TO THE ENTRANCE AS 

POSSIBLE WHILE ALLOWING A SECOND VEHICLE TO PULL UP TO THE 

AUTO SENTRY PETRO  WITH ENOUGH ROOM FOR THE CUSTOMER TO 

OPERATE IT WHILE THE FIRST CAR IS IN THE TUNNEL (MINIMALLY THIS 

DISTANCE IS TWELVE FEET FROM THE CENTER OF THE AUTO SENTRY 

PETRO TO THE NEAREST OBSTRUCTION).

ALL OF THE ABOVE FACTORS MUST BE TAKEN INTO CONSIDERATION 

WHEN DETERMINING THE BEST LOCATION FOR THE AUTO SENTRY PETRO 

IN RELATION TO THE ENTRANCE OF THE WASH BAY.  AS A GENERAL RULE, 

THE FURTHER AWAY THE AUTO SENTRY PETRO IS FROM THE BAY 

ENTRANCE, THE BETTER OFF IT WILL BE.

FACE OF BUILDING

THIS DRAWING IS NOT TO SCALE.

Summary of Contents for Auto Sentry Petro











































Reviews: