background image

TROUBLESHOOTING

No AC Output Voltage. No Indicator LEDs are illuminated:

- Check the DC wiring to the unit for loose connections or blown fuses.
- Ensure that the Power Switch is in the ON position.

No AC Output Voltage. Red Fault LED is blinking:

- The battery is discharged. The Inverter will  automatically restart when the battery voltage 
rises to at least 11.8 Vdc (23.6 Vdc for 24V Inverter / 47.2 Vdc for 48V Inverter).

No AC Output Voltage. Red Fault LED is on steady:

- The Inverter may be overloaded. Check that the Input Power requirements of the load do not 
    exceed the rated Output Power of the Inverter. Reset by cycling the Power Switch. 
- The battery voltage may be too high. The Inverter will automatically restart when the battery 
    voltage drops below 15.0 Vdc (30.0 Vdc for 24V Inverter / 60.0 Vdc for 48V Inverter).
- The Inverter may have overheated. The Inverter will automatically restart after it cools down. 
    Ensure that the unit has adequate ventilation if this happens.

PRODUCT SPECIFICATIONS 

 

 

 

 

ICT300-12SNV 

ICT300-24SNV 

ICT300-48SNV

  Input Voltage: 

 

 

10.5 - 16.0 Vdc  21.0 - 32.0 Vdc  42.0 - 64.0 Vdc

  Output Voltage:   

 

 

              115 Vac  

+/-

 5V

  Output Waveform:  

 

 

 

Pure Sine Wave

  Output Frequency:  

 

 

            60 Hz  

+/-

 0.05 Hz

  Total Harmonic Distortion (THD): 

 

 

     < 3% THD

  Continuous Output Power:   

 

 

     300 Watts

  Maximum Surge Power: 

 

 

        600 Watts (for 3 seconds)

  No Load Power Consumption: 

               

       4 Watts

  Efficiency (full load): 

 

        90% 

          91% 

          93%

  Peak Efficiency:   

 

      > 91% 

        > 91% 

          93%

  Input Current (maximum):   

     35 Amps 

      18 Amps 

        9 Amps

  Under Voltage Warning: 

            11.0 Vdc  

+/- 0.25 V

   22.0 Vdc  

+/- 0.5 V    

44.0 Vdc  

+/-1.0 V

  Under Voltage Shutdown:              10.5 Vdc  

+/- 0.25 V

   21.0 Vdc  

+/- 0.5 V    

42.0 Vdc  

+/-1.0 V

  Under Voltage Recovery: 

            11.8 Vdc  

+/- 0.25 V

   23.6 Vdc  

+/- 0.5 V    

47.2 Vdc  

+/-1.0 V

  Over Voltage Shutdown: 

            16.0 Vdc  

+/- 0.25 V

   32.0 Vdc  

+/- 0.5 V    

64.0 Vdc  

+/-1.0 V

  Over Voltage Recovery: 

            15.0 Vdc  

+/- 0.25 V

   30.0 Vdc  

+/- 0.5 V    

60.0 Vdc  

+/-1.0 V

  Operating Temperature: 

 

    

 

-20°C to +60°C

  Size (Length x Width x Height): 

 

 

9.6” x 5.3” x 1.7”

  Weight:   

 

 

                                       2.2 lbs

  Cooling:  

 

 

                Forced Air (Temperature Controlled)

  DC Input Connectors: 

 

                        1/4 Inch Bronze Studs

  AC Output Connectors: 

 

          Dual NEMA 5-15R North American Receptacles

  Chassis Grounding Connector: 

            8-32 Screw With Internal Tooth Lock Washer

6

Summary of Contents for SITE INVERTER 300









Reviews: