background image

ID Lock 202 Multi 

 

Installation manual 

V1.1 

 

14 

 

Definitions 

 

Door leaf:

 

 

Part of the door that opens/closes. 

Door frame:

 

 

Part of the door where the door leaf is attached. 

Door hinges:

   

Parts of the door that fastens the door leaf to the door frame. 

Mortise lock:   

Part of the lock that is inside the door leaf. 

Strike plate: 

 

Part of the lock that is inserted to the door frame. 

Outside unit:   

Part of the lock that is assembled on the outside door leaf. 

Cutting screw:

 

Screws that can be easily cut to adjust the length to door leaf depth. 

Inside unit: 

 

Part of the lock that is assembled on the inside of the door leaf. 

Inside backplate:

 

The part where the cutting screws are inserted fastened to the outside unit. 
Placed on the inside of the door leaf. 

Allen wrench: 

Tool to adjust the strike plate and fasten the door handle. 

Strike plate adapter:

 

Part for protecting the door frame against wear and making sure latches move 
with less friction over the strike plate edge. 

Mortise lock adapter:

 

Connects the inside unit to the dead bolt. 

Dead bolt: 

Part of the mortise lock that locks your door (see figure 16). 

Sensor latch: 

Part of the mortise lock that senses if the door is open or closed (see figure 
16). 

Latch:

 

Part of the mortise lock that moves when using the handles (see figure 16). 

Touch panel: 

Part of the outside unit with the numbers 0-9, * and # 

RFID reader:  

Part of the outside unit marked 

CARD

Key fob: 

 

 

Also called RFID. Point 14 in the contents picture on page 1. 

Automatic locking: 

ID Lock will lock automatically when you close the door (3 seconds delay). 

Relock:

 

ID Lock will relock if the door is not opened within 15 seconds after unlocking. 

Manual locking: 

When automatic locking is deactivated, you need to manually lock your door 
with the key button or by activating the touch panel. 

Lock when open: 

Activate by default, this means that you can force lock from the outside by 
holding the touch panel for a long time (more than 5 seconds). 

Master PIN:

 

The code you need to change access menus. 

Key button:

 

Inside the unit with a key symbol. Use it to lock/unlock and access the menu. 

Summary of Contents for 202 MULTI

















Reviews: