213
after 1 hour and another 1
℃
auto matically after 1hour.
3. After the setting of sleeping mode,the heating operation enables the set temperature to drop 2
℃
after
1 hour and another 2
℃
auto matically after 1hour.
4. The air condition runs in sleeping mode for 7hours and stops automatically.
Remark:
Press the mode or ON/OFF button,the remote controller clears sleeping mode away.
Timer button
: Press the button to set Timer ON/OFF, press the button then “ON” will flicker on the display
screen. then press
【
Clock +/- button
】
and to adjust hour that uses 12-hour clock including “A.M.” and
“P.M.” time; press the button again to complete the setting. The “OFF” setting is the same methods.
Remark:
W hen setting functions such as mode, temperature, swing and fan speed, display
screen displays all presetting parameters and remains constant; after reaching presetting time,
air conditioner will automatically start as per presetting state.
After setting timing ON and OFF function, pressing button of
【
Timer
】
can cancel timing setting.
Notes:
1. Time sequence of timing ON and OFF determines the order of “Timing ON-Timer OFF” and “Timer
OFF- Timing ON”. If the both are the same or either one is the same as time of current clock, it is
invalid to press “Timer” button to confirm presetting time; after it reaches the presetting time, it will
implement corresponding timing operation.
2. After setting time of timing ON and OFF, pressing “Timer” button can cancel timing.
3. Enter into time setting state of timing function; if there is no input related to time within consecutive 10
seconds, cancel the operation, return to previous state and go on with current time.
4. Default time of timer ON is 08:00 and default time of timer OFF is 18:00.
3.3 Installation of wired controller
◇
First, take apart the base panel from the wired controller.;
◇
According to the two installation holes on the install board, use two screws to fix the base panel to the
wall as shown below;
◇
Ensure that the connecting cable of the controller is accessible before connecting the wired controller to
the base panel.;
◇
Join the wired controller connection cable to the indoor unit using the cable provided.
Summary of Contents for ICC(ICA)-**HR-SA6-NI
