background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

British Gas RD1

 

Installation & Servicing

21

INSTALLATION

30 WATER CONNECTIONS

1.

Remove the plastic plugs from the flow and
return pipes.

2.

Make all water connections and check for
water soundness.

29 GAS CONNECTION

Refer to 'Gas Supply ', page 7.
Refer to Frame 2 for gas inlet service dimensions.

A  

minimum

 pressure of 20 mbar MUST be available at the boiler

inlet with the boiler operating. The main gas cock is on the left
hand side of the gas control valve, as shown. To facilitate
connection the gas cock may be removed from the gas control
valve.

28 FITTING THE KIT

1.

Remove the cardboard support aid from the
flue and place safely to one side.

2.

Fit the inner flue extension duct onto the
inner flue duct.

3.

Fit the outer flue extension duct onto the
outer air duct.

4.

Drill 3 - 3.2mm (

1/8

") dia. holes through the

outer air duct. 

Do not drill the inner flue

duct.

5.

Insert the self tapping screws provided to fix
the air duct in position.

6.

Repeat steps 1-5 if a second flue extension
is required.

31 ELECTRICAL CONNECTIONS

WARNING.

 The appliance must be efficiently earthed.

A mains supply of 230 V ~ 50 Hz is required.

All external controls and wiring must be suitable for mains
voltage. Wiring should be in 3-core PVC insulated & sheathed
cable, not less than 0.75mm

2

 (24 x 0.2mm) to BS. 6500 Table 16

Wiring Regulations and local regulations.

Connection must be made in a way that allows complete
isolation of the electrical supply - such as a double pole switch,
having a 3mm (1/8") contact separation in both poles, serving
only the boiler and system controls.  The point of connection to
the mains should be readily accessible and clearly marked.

Note.

For gravity DHW applications the pump MUST be wired
through the programmer and NOT directly to PL & PN.

1.

Remove the control box securing screws.  Swing the box
down into the servicing position. Refer to Frames 40 & 41.

2.

Route the mains cable into the box from the LHS of the
boiler.

3.

Connect the live and neutral wires into the terminal strip as
shown.

Note.

 

The boiler must be provided with this permanent supply

to terminal L & N.

4.

Connect the earth wire to the earth post.

5.

Secure the mains lead with the cable clamp.

IMPORTANT.

Control switching must not take place in this mains supply.

Terminal 
connection on 
(RHS) control 
support

Cla 1789

OH1 OH2 PL  PN EC1  EC2

Overheat thermostat

L N

Mains

br b y/g

Control box

PCB

Earth stud

Cla1790

INST

ALLA

TION

Summary of Contents for 30 RD1









































Reviews: