background image

4

5

Installation of Ideal relay transceiver

1.  Isolate power to boiler and heating system.

2.  Remove the cover of the relay transceiver and screw the base to the wall, 

directly above the existing system wiring if possible.

3.  Disconnect and dispose of the wiring to the existing two channel timer and 

room thermostat.  

4.  Make connections as in the diagrams below (except the opentherm wiring 

- see next steps overleaf).  Secure the wires in place using the cable clamps 
provided.

 

If a frost thermostat is connected it should be from live to connection 8 (C/S On)

5.  Power to the boiler and heating system should remain isolated.

Relay Transceiver

1

2

3

4

5

6

7

8

9

10

Opentherm

Boiler

opentherm

connector

Wiring 

centre

(not 

supplied)

L

N

E

R/S - Room Stat

HW - Hot Water

C/S - Cylinder Stat

bl

br

g/y

gr

or

w

KEY

- blue

- brown

- green/yellow

- grey

- orange

- white

Cylinder

Stat

1

C 2

Y plan

valve

or

bl

g/y

w

gr

Pump

(if external to boiler)

WEATHER

COMPENSATION

OPENTHERM

Opentherm

Pump

(if external to boiler)

Relay Transceiver

1

2

3

4

5

6

7

8

9

10

R/S - Room Stat

HW - Hot Water

C/S - Cylinder Stat

Cylinder

Stat

1 C

DHW

valve

CH

valve

g/y

bl

gr

or

or

br

bl

gr

g/y

br

wiring 

centre

(not 

supplied)

bl

br

g/y

gr

or

KEY

- blue

- brown

- green/yellow

- grey

- orange

Boiler

opentherm

connector

L

N

E

WEATHER

COMPENSATION

OPENTHERM

Ideal relay transceiver wiring (Y plan diagram)

Ideal relay transceiver wiring (S plan diagram)

*Where the Ideal Touch kit is being fitted to an existing installation (S or Y plan),  the wire 
connecting any SL IN on the boiler requires disconnecting and making safe.  A link wire 

should then be connected into the SL1 L-IN connection at the boiler†. 
For further details refer to the boiler installation and sevicing instructions.  
†Logic Heat H, Logic System S, Vogue Gen2 System

Summary of Contents for touch










Reviews: