background image

3

IMAX XTRA 2 - 

QAA55 Room Thermostat Kit Instructions

INSTRUCTIONS

1.3  FITTING THE QAA55 ROOM THERMOSTAT

The room thermostat should be installed approximately  

1.5m high on a wall located in the space to be heated.  

Avoid locations affected by draughts created by windows /

doors, or heating effects created by independent heaters.
A room thermostat must not be fitted to an area were 

radiators are controls by TRV's fitted on the radiators.

Use a small flat bladed screwdriver to remove the room 

thermostat cover as shown in Fig.3

Use a minimum of 2 screws (not supplied) to fix the Room 

Thermostat back plate to the wall, as shown in Fig.4.

Fig. 4

Fig. 3

Feed the 2-wire cable through the rear, or the top, of the 

back plate and connect the wiring as follows: 
1. 

Connect the red wire to pin 1 of connector  

 

 

(CL+ BSB Data)

2. 

Connect the black wire to pin 2 of connector    

 

(CL- BSB Ground)

These connections are shown Fig.5.

Fig. 5

Place the cover back onto the back plate, as shown in Fig.6.

Fig. 6

Rear

Top

For rear entry, route 

the cable through 

the rear prior to 

fixing to the wall.

Summary of Contents for QAA55









Reviews: