Ideal Vacuum Habanero P1012726 User Manual Download

Page: 7 / 19

info@idealvac.com

www.idealvac.com

HRCF-08122022 - V 1.1

1.2 PHYSICAL SPECIFICATIONS

Parameter

Value

Maximum Heater Temperature

900

C (1652

Minimum Heater Temperature

Ambient

Window Diameter/Type

Ø1” Uncoated UV Fused Silica, 5 mm Thick,

0.5

Wedge, Wavelength Range: 185-2100 nm

Maximum Window Thickness

8 mm (0.315 in.)

Heater Type

Ceramic Fiber

Heater Bore Diameter

50.8 mm (2.0 in.)

Cell Holder Material

Macor Ceramic

Maximum Cell Holder Sample Diameter

26 mm (1.024 in.)

Maximum Cell Length (in Holder)

139.7 mm (5.5 in.)

Maximum Mounting Rod Sample Diameter

41.3 mm (1.625 in.)

Maximum Cell Length (on Mounting Rods)

155 mm (6.1 in.)

Heater Sheath Material

304 Stainless Steel

Case Material

10 ga. 5052 H32 Aluminum

Maximum Case Temperature

130

C (266

Cooling

Passive Convection

Power Input

100-120 VAC, 50/60 Hz

Maximum Current

3.6 A

Heating Power

425 W

Power Cable

118 cm (3.9 ft.) long with NEMA 15-5 plug

Thermocouple Cable

118 cm (3.9 ft.), Type K Mini Male Connector

Recommended Controller

IVP PID Heater Controller (P107361)

Physical Dimensions

212 x 129 x 142 mm (8.34 x 5.08 x 5.60 in.)

Minimum Top Clearance

305 mm (12 in.)

Minimum Side Clearance

76 mm (3 in.)

Recommended Underneath Clearance

76 mm (3 in.)

Weight

5.33 kg. (11.75 lb.)

Table 1 - Furnace specifications

Summary of Contents for Habanero P1012726




















Search results

Summary of Contents for Habanero P1012726

Reviews:

Related manuals for Habanero P1012726

Brands by name

Popular brands

Ideal Vacuum Habanero P1012726, User Manual

Search results

Summary of Contents for Habanero P1012726

Reviews:

Related manuals for Habanero P1012726

Brands by name

Popular brands