background image

TLX-7000 

Aug 2021

 

SAFETY INFORMATION 

 

Note, Caution and Warning 

 

This document uses the following notations: Note, Caution and Warning 

– to alert you to special instructions, 

tips, or hazards for a given procedure. Please familiarize yourself with the notation explanations described 
below.  
  
 

Indicates important information that requires special attention, such as a procedure for a 
specific vehicle, or tips on operating the equipment. 

 
 
 

Indicates the potential for damage to equipment, accessories, or the vehicle unless the 
instructions or procedure are followed specifically. 

 
 
 

Indicates the potential for property damage, personal injury, or death due to hazards 
associated with the equipment, vehicle, or environment.  Do not perform any procedures 
until you have read and understood the warning instructions. 

 

Important Information 
 

1. 

Read this manual thoroughly

 before installing, operating, or maintaining the lift. 

 

2. 

This lift is rated to 7,000-lbs lifting capacity

. NEVER EXCEED rated lifting capacity of lift. 

 

3. 

This lift is designed for indoor & outdoor use

 and should not be installed in a pit or depression. 

 

4. 

The floor/surface on which the lift is to be used should be smooth and flat

 as possible.  

 

5. 

The lift has specific mechanical requirements

 as described in the Installation Instructions section of 

this manual. 
 

6. 

This lift has a minimum vehicle height requirement

 as described in the Installation Instructions 

section of this manual. 
 

7. 

Failure by the owner / operator to provide the power drill requirements, proper surface, and 
recommended shelter

 (when not in use) could result in unsatisfactory lift performance, property 

damage, or personal injury. 
 

8. 

Do not attempt to install / assemble this lift

 if you have never been trained on basic automotive lift 

installation procedures. 
 

9. 

Stay clear of any moving parts

 that cause injury.  

 

10. 

The operation of the lift is permitted by authorized persons

 only.

 

Summary of Contents for 7000TLX


















Reviews: