background image

25

INSTALLATION

Ideal Logic Heat - 

Installation and Servicing

 FLUE OUTLET

 

27

  MOuNTINg THE BOILER - REAR FLuE OuTLET KIT (55/80)

1. 

Remove the rear flue blanking disk.

2. 

Lift the boiler onto the wall plate, (refer to the 
introduction section for safe handling advice), 
ensuring the boiler is offered to the bracket tabs at 
an angle as shown below, and carefully allow the 
boiler to swing down to the wall as this movement 

engages the rear flue air and flue seal.

3.

  Screw the boiler bottom retaining bracket to the 

wall with the screw provided.

4.

  Remove the top flue blanking disk refer to     

Frame 26.  Fill the condensate trap within the 

boiler by pouring a cupful of water into the flue 

outlet.  Take care to ensure that the water is only 

poured into the flue outlet, and does not spill into 

the boiler casing.  

5. 

Replace the top flue blanking disc and retain with 

the horseshoe bracket and fixing screw previously 

removed.

  During assembly check that the flue seals do not 

become dislodged.

205862-10097

3

1

Summary of Contents for Logic HEAT 12









































































Reviews: