Switches &
Pilot Lights
Display
Lights
Display
Units
LED
Illumination
Units
Safety
Products
Terminal
Blocks
Comm.
Terminals
AS-Interface
Relays &
Timers
Sockets
Circuit
Protectors
Power
Supplies
PLCs &
SmartRelay
Operator
Interfaces
Sensors
Control
Stations
Explosion
Protection
References
Flush
Silhouette
709
HS5E Miniature Interlock Switches with Solenoid
Actuators
Description
Actuator Retention Force
Part No.
Straight
1400N minimum
HS9Z-A51
Straight w/rubber bushings
HS9Z-A51A
Right-angle
HS9Z-A52
Right-angle w/rubber bushings
HS9Z-A52A
Angle Adjustable (vertical)
HS9Z-A53
Angle Adjustable (vertical/horizontal) (Note 1)
500N minimum
HS9Z-A55
Sliding Actuator (Note 2)
1000N minimum
HS9Z-SH5
Note 1: When retention force of more than
500N is required, use HS9Z-A53.
Note 2: For details, see page 746.
26
15
32.4
28
20
10
0.8
5.2
(6)
6.2
6.4
2
20
Actuator Stop
(supplied with the actuator)
(Note)
4-R 2.2
Actuator Mounting Hole Layout
(Straight, L-shaped)
2-M4 Screw
49
15
7
18.5
29
3
3.6
1
R2.1
23
26
38
38
0.8
2
Angle Adjustment
(M3 Hexagon Socket Head Screw)
Angle Adjustment
(M3 Hexagon Socket Head Screw)
Actuator Stop
(Note)
Actuator Stop
(Note)
2-M4 Screw
Actuator Mounting Hole Layout
(horizontal/vertical swing)
Vertical Adjustment
Horizontal Adjustment
Orienting
Insert
Orienting
Insert
20
°
20
°
(M4 Holes)
Actuator Stop
Film (supplied
with the actuator)
Door hinge side
20
5
R3.2
72
58
44
33 max.
12
(21)
1
20°
29
Angle Adjustment
(hexagon sockethead bolt)
58
2-M6 Screw
Actuator Mounting Hole Layout
(vertical swing)
18
30
7.3
43.8
15.3
15
2-ø4.3
2
12
0.8
(20)
0.8
2-ø10
2-ø9
When mounted (5)
V
e
rtical Swing
Washer (supplied with the switch)
Rubber Bushing
Actuator Stop (Note)
•
The mounting center distance is set to 12 mm
at factory. When 20-mm distance is required,
ad
j
ust the distance by moving the rubber
bushings.
•
The actuator has fle
x
iblity to the direction
indicated by the arrows. When 20-mm distance
is selected, the actuator swings vertically.
12
2-M4 Screw
Actuator Mounting
Hole Layout
Straight (with rubber bushings)
Right-angle (with rubber bushings)
Note: Mounting centers can be widened
to 20 mm by moving the rubber
bushings.
Dimensions and Mounting Hole Layouts
Note: The actuator stop is supplied with the actuator and used when adjusting the actuator
position. Remove after the actuator position is determined.
•
When the mounting center distance is set to
12 mm, the actuator has fle
x
ibility both
vertically and horizontally.
•
When the mounting center distance is set to
20 mm, the actuator swings vertically. Ad
j
ust
the distance by moving the rubber bushings.
30
15
Horizontal
Swing
V
e
rtical
Swing
15.8
8.5
0.8
2
0.8
When mounted (11.2)
When mounted
(39.7)
When mounted (5)
2-ø9
2-ø10
2-ø
4.3
12
(20)
Actuator Stop (plastic) (Note)
(supplied with the actuator)
Rubber Bushing
Washer (supplied
with the actuator)
15
Acuator Stop (supplied with the actuator) (Note)
Actuator Cover
2
2-ø4.4
20
33
30
28
0.8
4.5
2
7.2
7.2
1.6
Straight Actuator (HS9Z-A51)
Straight Actuator w/Rubber Bushings (HS9Z-A51A)
Angle Adjustable (vertical) (HS9Z-A53)
Angle Adjustable (vertical/horizontal) (HS9Z-A55)
Right-angle Actuator (HS9Z-A52)
Right-angle Actuator w/Rubber Bushings (HS9Z-A52A)
Actuator Orientation
The orientation of actuator swing (horizontal/vertical) can be changed using the
orienting insert (white plastic) installed on the back of the actuator. Do not lose
the orientating insert, otherwise the actuator will not swing properly.
HS5E
