background image

  

BLENDORAMA III 

 

 

 

13

 

2.  When the brush is too dirty and does not clean the nozzle of the 

canister, rinse and clean the brush. See 

§ 3.3.3

.

 

3.  When the nozzles are too dirty, clean the nozzles individually 

with a damp cloth. See 

§ 3.3.4

.

 

3.3.3 

Cleaning the brush unit: daily 

The brush unit removes the excess colorant from the nozzles. 

The brush unit consists of a brush container and a removable 
brush that rotates. The brush unit is installed in a bracket with a 
click connection.

 

It is advised to replace the brush unit every 4 months to ensure 

optimal performance. Replacement brush units are provided in 
the Blendorama  Maintenance Kit.

 

Note 

If you do not clean these items daily, mistinting might 
occur.

 

1.  Slide the brush unit (A) out of the bracket (B).

 

2.  Remove the rotary brush (C) from the brush container (D).

 

3.  Remove the fluids from the brush container.

 

Note 

For the disposal of the fluids, follow the local 
regulations.

 

4.  Rinse and clean the static brushes (E).

 

5.  Rinse and clean the rotary brush.

 

6.  Place the rotary brush back in the brush container.

 

 

 

 

 

 

 

 

 

Summary of Contents for Blendorama III Series


























Reviews: