IDTECK FINGER006SR Quick Installation Manual Download

Page: 3 / 17

※

FINGER006 SERIES QUICK INSTALLATION GUIDE

3. PARTS CODE AND DESCRIPTION

* As long as there is not mention, contents below are applied to FINGER006, IP-FINGER006, FINGER006SR equally.

3.1 Front Panel

LCD Display

LCD displays

FINGER006

’s status.

3 LED Indicators (showing system status)

The red LED turns on with power supply.

                    The green LED turns on if access has granted.    .
                    The orange LED turns on if access has failed.

Finger Print Scanner

When users put their finger on the scanner, white light will turn on.

16 Numeric Keypad

Card data registration, deletion and various function settings are possible through keypad input without

host computer control.

Function Keypad

There are four function keys: F1, F2, F3 and F4

LCD Display

Fingerprint
Scanner

3 LED Indicators

(showing system status)

16 Numeric Keypad

Function Keypad

Summary of Contents for FINGER006SR


















Search results

Summary of Contents for FINGER006SR

Reviews:

Related manuals for FINGER006SR

Brands by name

Popular brands

IDTECK FINGER006SR, Quick Installation Manual

Search results

Summary of Contents for FINGER006SR

Reviews:

Related manuals for FINGER006SR

Brands by name

Popular brands