IDTECK FINGER006SR Quick Installation Manual Download

Page: 7 / 17

※

FINGER006 SERIES QUICK INSTALLATION GUIDE

4. INSTALLATION TIPS & CHECK POINT

* As long as there is not mention, contents below are applied to FINGER006, IP-FINGER006, FINGER006SR equally.

Installing the

Star FINGER006/ iPASS IP-FINGER006 / IDTECK FINGER006SR

is an easy task. It can be installed

with common hand tools and readily available communications wires.
This section provides information about wiring, wire runs and other information to make the installation quick and easy.

4.1 Check Points before Installation

4.1.1 Selection of Cable

System installation cabling will be configured as follow:

Figure: System Installation Layout

4.1.2 Recommended Cable Type and Permissible Length of Cable

Reference

Description

Cable Specification

①

FINGER006 Power (DC12V)
DC Power

FINGER006

Belden #9409, 18 AWG

2 conductor, unshielded

Summary of Contents for FINGER006SR


















Search results

Summary of Contents for FINGER006SR

Reviews:

Related manuals for FINGER006SR

Brands by name

Popular brands

IDTECK FINGER006SR, Quick Installation Manual

Search results

Summary of Contents for FINGER006SR

Reviews:

Related manuals for FINGER006SR

Brands by name

Popular brands