background image

 
 
                                                                                                                 

   

 

  9       

User’s Manual 

 

10. FCC Registration Information 

 

FCC REQUIREMENTS PART 15 

 

Caution: 

Any changes or modifications in construction of this device which are not expressly 

approved by the responsible for compliance could void the user's authority to operate the equipment

 

NOTE: 

This device complies with 

Part 15 of the FCC Rules

 

Operation is subject to the following two conditions; 

1. This device may not cause harmful interface, and 

2. This device must accept any interference received, including interference that may cause 

undesired operation. 

 

This equipment has been tested and found to comply with the limits for a 

Class A Digital Device

pursuant 

to Part 15 of the FCC Rules

. These limits are designed to this equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. 

However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be determined 

by turning the radio or television off and on, the user is encouraged to try to correct interference by 

one or more of the following measures. 

 

1. Reorient or relocate the receiving antenna. 

2. Increase the separation between the equipment and receiver. 

3. Connect the equipment into an outlet on another circuit. 

4. Consult the dealer or an experienced radio/TV technician for help. 

Summary of Contents for Star RF10













Reviews: