background image

ID GATE 6000 Electromechanical Tripod Turnstile 

29 

 

 

 

 

APPENDIX 1.   Control signal algorithm at pulse control mode

 

   

Note:

 

For the RC panel: 

 

active front 

 pressing of the relevant button on the RC panel; 

 

low level

 the relevant button on the RC panel has been pressed; 

 

high level 

 the relevant button on the RC panel has not been pressed. 

 

The command is a signal active front (signal transfer from the high level to the low level) at 
any  of  the  contacts  at  presence  of  the  corresponding  signal  levels  at  the  other  contacts. 
The  following  commands  can  be  formed  by  sending  a  low-level  signal  to  the  contacts 

Unlock  A

”,

 

Stop

 and 

Unlock  B

 of  the 

XT1.L 

connector  block  relatively  to  the  contact 

GND

”:

 

Always locked (locked for entry and exit)

 

Active  front is  at the  contact 

Stop

  while  there  is  a high  level  at  the  contacts 

Unlock  A

 

and 

Unlock B

”.

 Both passage directions are locked at this command. 

 

Single    passage    in    the    direction    A    (open    for    passage    of    one    person 
in the direction A)

 

Active  front is  at the  contact 

Unlock A

  while  there  is  a high  level  at the  contacts 

Stop

 

and 

Unlock B

”.

 

 

At this command the passage direction A opens either for 5 sec. or until the passage has 
been made in this direction or until the command 

«Always locked»

, and the status of the 

passage    direction    B    does    not    change    at    that.    The    command    is    ignored    if 
at the moment of its receipt the status of the passage direction A is 

«Always free»

 

Single    passage    in    the    direction    B    (open    for    passage    of    one    person 
in the direction B)

 

Active  front is  at the  contact 

Unlock B

  while  there  is  a high  level  at the  contacts 

Stop

 

and 

Unlock A

”.

 

 

At this command the passage direction B opens either for 5 sec. or until the passage has 
been effected in this direction or until the command «Always locked», and the status of the 
passage  direction  A  does  not  change.  The  command  is  ignored  if  at  the  moment  of  its 
receipt the status of passage direction B is «Always free». 

 

Bi-directional single passage (open in both directions 

for ‘one

-by-

one’

 passage) 

Active front is at the contact 

Unlock A

 while there is a low level at the contact 

Unlock B

” 

and a high level at the contact 

Stop

”,

 

or  active  front  is  at  the  contact 

Unlock  B

  while  there  is  a  low  level  at  the  contact 

Unlock A

” and a high level at

 

the contact “

Stop

”.

 

 

At  this  command  the  both  passage  directions  open  either  for  5  sec.  each  or  until  the 
passage has been effected in the given direction or until the command 

«Always locked» 

is  received.  The  command  is  ignored  for  the  passage  direction,  which  status  at  the 
moment of its receipt is 

«Always free»

 

Free passage in the direction A (open for free passage in the direction A)

 

Active front is at the contact 

Unlock A

 while there is a low level at the contact 

Stop

 and 

a high level at the contact 

Unlock B

”,

 

or active front is at the contact 

Stop

 while there is a low level at the contact 

Unlock A

 

and a high level at the contact 

Unlock B

”.

 

 

At  this  command  the  passage  direction  A  opens  until  the  command 

«Always  locked» 

is 

received; the status of the passage direction B does not change at that. 

Summary of Contents for TTR-08

































Reviews: