background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IEI Support URL 

https://new.ieiworld.com/en/online_support_form/index.php 

 

 

Compliance 

 

 

This equipment has been tested and found to comply with specifications for CE marking. If the user modifies 

and/or installs other devices in the equipment, the CE conformity declaration may no longer apply. 

 

 

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

 

This device may not cause harmful interference, and 

 

This device must accept any interference received, including interference that may cause 

undesired operation. 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference when the equipment is operated in a commercial environment. This equipment generates, uses, 

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 

manual, may cause harmful interference to radio communications. Operation of this equipment in a 

residential area is likely to cause harmful interference in which case the user will be required to correct the 

interference at his own expense. 

 

 

According to the requirement of the WEEE legislation the following user information is provided to customers 

for all branded IEI Electronics products subject to the WEEE directive. 

This symbol on the product or on its packaging indicates that this product must not be disposed of with your 

other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over 

to a designated collection point for the recycling of waste electrical and electronic equipment. The separate 

collection and recycling of your waste equipment at the time of disposal will help to conserve natural 

resources and ensure that it is recycled in a manner that protects human health and the environment. For 

more information about where you can drop o- your waste equipment for recycling, please contact your local 

city office, your household waste disposal service or the shop where you purchased the product. 

 
 

 

Headquarters 

威強電工業電腦股份有限公司

 

IEI Integration Corp. 

22161

新北市汐止區中興路

29

 

No. 29, Zhongxing Rd., Xizhi Dist.,   

New Taipei City 22161, Taiwan 

TEL: +886-2-86886-2-26902098 

FAX: +886-2-66160028 

sales@ieiworld.com 

 

www.ieiworld.com

 

America 

IEI Technology USA Corp. 

138 University Parkway, Pomona,   

CA 91768, USA 

Tel:+1-909-595-2819 

Fax:+1-909-595-2816 

sales@usa.ieiworld.com 

usa.ieiworld.com

 

China 

威强电工业电脑

 

 

上海市闵行莘庄工业区申富路

515

 

No. 515, Shen Fu Rd., Xin Zhuang Industrial 

Develop Zone, Shanghai, 201108, China 

Tel:+86-21-3116-7799 

Fax:+86-21-3462-7797 

sales@ieiworld.com.cn 

www.ieiworld.com.cn

 

 

 

Copyright ©2018 IEI Integration Corp. All rights reserved       

 

Summary of Contents for BRICK Series









Reviews: