background image

           PSC-586VGA

ISA/PCI Pentium™

 w/ VGA

  Single Board Computer

@Copyright 1996
All Rights Reserved.
Manual first edition May 05,1996
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.

Trademarks

PSC-586VGA is registered trademarks of Acquire Inc.,IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a
registered trademark of Intel Corporation. AMI is registered trademarks of
American Megatrends, Inc. Other product names mentioned herein are used
for identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.

Summary of Contents for PSC-586VGA
































Reviews: