background image

21

UK

 

► Press [Set] and keep it 

pressed�

The flashing digit is increased, 9 is followed by 0 and the first 

new digit (left) becomes active�

8 �1 8 3

[Set] permanently pressed 8 �1 9 3

[Set] kept pressed 8 �1 0 3

If digit 1 is increased this way, the display changes to the 

next higher setting range (9 is followed by 10)�

8 �1 2 3

[Set] permanently pressed 9 �1 2 3

[Set] kept pressed 1 0 �1 2

 

► Press no pushbutton 

for 3 s�

The digit following on the right flashes (= becomes active)� 

If the fourth digit flashes unchanged for 3 s, digit 1 becomes 

active again (if the value of digit 1 is > 0)�

8 �1 2 3

no pushbutton pressed; after 3 s 8 �1 2 3

after 3 s 8 �1 2 3
after 3 s 8 �1 2 3
after 3 s 8 �1 2 3

If digit 1 has the value “0”, the display changes to the next 

lower setting range�

0 1 �2 3

no pushbutton pressed; after 3 s 0 1 �2 3

after 3 s 0 1 �2 3
after 3 s 0 1 �2 3

after 3 s (new digit 4 active and set to 0) 1 �2 3 0

after 3 s (new digit 1 active) 1 �2 3 0

Highlighted grey ( 1 ) = flashing digit

Note: If [Set] is pressed continuously, the display moves through all setting ranges; 

after the end value it jumps back to the start value� Release [Set] briefly and start 

the setting again�

Summary of Contents for efector300 SD6001
























Reviews: