background image

CR3158

mobileIoT gateway

6

4 Function

The device has a buffer capacitor to store the time in the real time clock (RTC).

The device provides access to CAN data in various operating modes.

Function

CR3158

CAN-CAN-Bluetooth/WLAN bridge

CAN-Bluetooth/WLAN interface

Antenna

external

Mobile communications

4G worldwide (certified countries only)

Real-time mode

Cloud logging mode

Input/output functions

3/1

Acceleration sensor

Gyro sensor

GNSS

CAN connections

3

ifm e-SIM

● = applicable

4.1 Mobile radio interface

The unit has a mobile radio interface for mobile data transmission.

The unit supports the 4G mobile network. In order to achieve higher network coverage, the unit has a
fallback function, allowing it to switch to the 2G or 3G network.

The unit detects the mobile network with the best transmission speed and automatically switches to it.
The mobile radio interface supports bidirectional data exchange in the mobile network.

4.2 eSIM card

The unit is equipped with an embedded SIM (eSIM) card. The eSIM card is delivered with an eSIM
profile that contains all the necessary communication settings.

The eSIM card of the unit is not activated on delivery. After registering the unit, activation of the
eSIM card can take up to 4 hours.

4.3 Connection modes

The device can be operated in the following connection modes:

Real-time mode

Cloud logging mode

The connection mode is set as follows:

Object

Index

Subindex

Type

Default

Description

DeviceMode

0x5353

0x00

U8

0x03

0X00 = cloud logging mode

0x01 = reserved

0x02 = real-time mode

Summary of Contents for CR3158

























Reviews: