IFM DTE800 Operating Instructions Manual Download | Manualshive

Page: 13 / 15

background image

UK

RFID UHF reader

13

Circuitry of the inputs not electrically isolated

7.4.2 Digital outputs

The outputs are also electrically isolated from the operating voltage of the reader

and have a common pole (switching output CMN)�
If the electrical isolation is not needed, the operating voltage can also be obtained

directly from the reader�

Circuitry of the outputs electrically isolated

«
...
11
12
13
14
15
»

Summary of Contents for DTE800
















Reviews:

No comments

Related manuals for DTE800

Brand: IBM Pages: 72

OneFlow OFTWH-R

Brand: Watts Pages: 8

Brand: M-system Pages: 6

Brand: Nexus 21 Pages: 24

Brand: Magnavox Pages: 23

Brand: HEEVE Pages: 16

Brand: VAT Pages: 53

Brand: Belson Pages: 34

Brand: Lifter Pages: 170

Lumina LU20S-DNW

Brand: Leviton Pages: 3

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 18

Brand: AutomationDirect Pages: 8

Brand: Huntleigh Pages: 32

Brand: Aqua Control Pages: 16

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands