background image

mobileIoT gateway

CR3145

15

5 Installation

u

Disconnect the power of the machine before installation.

The unit can be mounted in a horizontal position or with the connectors facing downwards.
Installation with the connectors facing upwards is not permitted.

The unit must be fixed with the rear facing the mounting surface.

ATTENTION

Higher shock > IK07

w

Damage possible
Protection rating and electrical protection might be impaired

u

If necessary, the system creator must take external measures to protect the device
depending on the requirements of the corresponding application.

u

Replace damaged units, otherwise the technical data and safety will be impaired.

74

Fig. 1: Holes for mounting

u

Use 2 M5x30 cylinder head bolts to fix the unit on an even surface.
Tightening torque: 2.2 Nm

5.1 Mounting the antennas

u

When mounting the antennas in vehicles avoid the vicinity of fuel tanks, vessels with explosives or
insufficiently screened electronic components (→ 2 Safety instructions).

u

Position the antennas so that a permanent distance of min. 0.2 m from people is ensured during
operation.

u

Do not install the antennas in closed metal constructions such as the driver's cab.

u

To reliably receive the GPS signals, position the GPS antenna with unrestricted access to the sky.

u

Please observe the antenna manufacturer’s notes.

Stable data transmission requires a good antenna signal. In case of problems change the
position of the antennas or the mobile equipment if necessary.

GB

Summary of Contents for mobileIoT CR3145























Reviews: