background image

18 

 

 

If this cleaning was not sufficient, dismount bottom/cover flange (2.3) and remove float (2.1). 

 
 

Plant must be pressureless for disassembly works! 
Wait until unit has cooled! 

 
 

  Close shutoff valves (W+D). 

  Open drain valve (A) / plug (6); unit is drained. 

  Caution! When dismounting, residual medium may escape and further evaporation is also 

possible. 

  Remove cover flange (2.3). 

  Remove float and clean standpipe and float. 

  Insert float with top-heavy side upwards into standpipe (top-heavy side with colour 

marking). 

  Always use new gaskets (2.2) when assembling the unit. Tighten bolts of cover flange / 

standpipe in several steps using successively opposite diagonal tightening (see table in 
chapter 9.2) until reaching tightening torque Md

 max

 

Close shutoff valves before carrying out preservation works or chemical 
cleaning of the boiler. Or even better: interrupt passage on flange 
connection of boiler nozzles by placing blind flanges. 
 
 
 

For commissioning see chapter 9. 
 
Design sketch see chapter 6 
 
 

10.2 Tightening torques 

 

all. 

pressure 

PS

 

 

[bar] 

Tightening torque Md 

 

Md

 max 

[Nm]

 

in steps 

32 

35 

50 

65 

75 

50 

50 

75 

100 

125 

150 

165 

 

Tightening torques of screw plug (6) Md= 

150 Nm

 

 

 

 

Danger

 

 

Danger

 

Summary of Contents for NA7-50

























Reviews: