background image

  19 / 27 

7.

 

Storage condition: Test Strips 39°F

86°F (4°C

30°C), Humidity 10%

85%RH 

The meter -4°F

131° F (-20°C

55°C); Humidity 10%

80%RH 

8.

 

Operating conditions: 50°F

104°F (10°C

40°C) , 25%RH

80%RH 

9.

 

Blood source: Fresh capillary whole blood 

10.

 

Blood volume: Minimum 0.7 micro liter 

11.

 

Life span: Five years 

12.

 

If you are taking acetaminophen containing drugs (Tylenol and other medicines containing 

acetaminophen, blood concentrations >5 mg/dL) or Vitamin C (ascorbic acid, blood concentrations >4 

mg/dL) at doses higher than recommended, these may interfere with your glucose meter and cause 

you to get inaccurate results with this system 

MAINTENANCE AND STORAGE OF YOUR METER 

 

Always  use  care  when  handling  the  iHealth  Wireless  Smart  Glucose  Meter  (BG5S).  Dropping  or 
throwing the meter may cause damage. 

 

Always wash your hands with soap and water, and rinse and dry them completely before handling the 

iHealth Wireless Smart Glucose Meter (BG5S) and test strips. 

SYSTEM TROUBLESHOOTING 

If  you  follow  the  recommended  action  but  the  problem  persists,  or  error  messages  other  than  the  ones 

below appear, 

please call iHealth Labs Customer Service at 1-855-816-7705

. Do not attempt to repair the 

meter by yourself and never try to disassemble the meter under any circumstances. 

Display Messages 

MESSAGE 

WHAT It Means? 

ACTION 

 

Blood glucose level is lower 
than 20mg/dL 
(1.1mmol/L) 

- Repeat the test using a new 
test strip. 
- If your result still flashes Lo, 
seek medical advice 
immediately. 

 

Blood glucose level is higher 
than 600 mg/dL 
(33.3mmol/L) 

- Wash and dry your hands, 
and the test site, thoroughly. 
Repeat the test using a new 
test strip. 
- If your result still flashes HI, 
seek medical advice 
immediately. 

Summary of Contents for BG5S































Reviews: