5
This unit features a Lightning dock (located on top of the unit) exclusively to play and charge iOS devices equipped with
the latest Lightning connector. There is also a USB port (located on back of the unit) which can play and charge older iOS
devices (such as iPhone 4, iPad, etc.) and Lightning devices using the charging cable that came with the device.
Note: The USB Dock cannot charge iPad models later than iPad 2
.
Play and pause a device connected to the Lightning docks using the
Dock Button
and play and pause a device
connected to the USB port using the
USB Button
. Only one device can play at a time. Directions below apply to
whichever dock/port you wish to control.
1.
Connecting using the Lightning Dock
:
While the dock accommodates most cases, you may need to remove your case for proper docking.Dock an already
playing Lightning-capable iPad/iPhone/iPod in the Lightning Dock on top of the unit. The unit will automatically turn
on and you will hear the audio playing from your iPad/iPhone/iPod.
Connecting using the USB port
:
Connect your iPad, iPhone or iPod to the USB port located on back of the unit using the USB charging cable that
came with it.
Note:
If the audio source volume is too low on the iPad/iPhone/iPod, the unit may not detect that the iPad/iPhone/iPod is
in play mode. If so, pressing the
Dock Button
or the
USB Button
on the unit once should make it play.
2. When an iPhone/iPod is docked to the Lightning dock or connected to the USB port and in standby mode, press the
Dock Button
or the
USB Button
on the unit to play the iPad/iPhone/iPod. If the unit is already on, press and
release the
Mode Button
as needed until “Dock” or “USB Dock” appears on the lower part of the display, indicating
which dock/port on the unit is in iPod mode. If your iPad, iPhone or iPod touch is in video mode, you may see the
“locked” slider on the iPad/iPhone/iPod display. If so, you will need to unlock your iPad/iPhone/iPod.
3. Press the
Dock Button
or the
USB Button
on the unit on the unit to pause play; press again to resume play.
4. Press the
+
or
– Button
on the unit to go to the next or previous track. Press and hold while track is playing for high
speed forward or reverse music search of the current track.
Adjusting Sound on the Unit
You can adjust the sound on the unit while listening to any sound source.
1. Press the or
Button
on the unit to adjust the system volume.
2. Press and release the
EQ Button
as needed to select Treble, Bass, Balance or 3D sound effect, then press the
+
or
– Button
to adjust settings.
Snooze Operation
1. Default snooze time is 9 minutes. To program a custom snooze time, press and hold the
Snooze Button
during normal
operation (when alarm is not sounding) until the snooze minutes display appears. Press and release the
+
or
- Button
to
set the snooze timer from 1 to 29 minutes. Press and release the
Snooze/Dimmer Button
to exit snooze setting mode
.
2. Press and release the
Snooze/Dimmer Button
after an alarm sounds. The alarm will be silenced for the set snooze
duration time then sound again. Snooze can be pressed several times during the 1 hour alarm cycle.
Sure Alarm
The unit has a sure alarm feature. If back-up batteries are installed, the buzzer alarm will still sound in the event of a
power failure.
6
Listening to iPad, iPhone or iPod Using the Dock or USB Port
Listening to Radio
Setting up the Antenna
Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.
Tuning and Playing the Radio
1. Press and release the
Mode Button
as needed to cycle through Dock, USB Dock, FM radio and Aux-in modes.
2. When FM mode is selected, press the
+
or
– Button
to tune the radio to a desired station. The current radio frequency
appears in the lower right of the display. Press the
+
or
– Button
for a few seconds to scan for the next clear station.
