IHP BarcelonaLights36ZEN Installation And Operation Instructions Manual Download

Page: 37 / 40

900861-00NC

IHP.us.com

REPLACEMENT PARTS

Continued

Item

Description

Part Number

36” Complete Stainless Steel Burner Pan Assembly

F3458

48” Complete Stainless Steel Burner Pan Assembly

F3459

60” Complete Stainless Steel Burner Pan Assembly

F3460

72” Complete Stainless Steel Burner Pan Assembly

F3461

Bottom Support Fin for 36” Model - 2 per unit

(Figure 10, Page 13)

F3462

Bottom Support Fin for 48” Model - 2 per unit

(Figure 10, Page 13)

F3463

Bottom Support Fin for 60” Model - 2 per unit

(Figure 10, Page 13)

F3464

Bottom Support Fin for 72” Model - 2 per unit

(Figure 10, Page 13)

F3465

LED Tray Assembly - Left 36”

F3491

LED Tray Assembly - Left 48”

F3492

LED Tray Assembly - Left 60”

F3493

LED Tray Assembly - Left 72”

F3494

LED Tray Assembly - Right 36”

F3495

LED Tray Assembly - Right 48”

F3496

LED Tray Assembly - Right 60”

F3497

LED Tray Assembly - Right 72”

F3498

1/2” Flex Gas Line (46-inch Length)

F3466

Air Shutter Orifice NG (for 36” Natural Gas Models)

F3467

Air Shutter Orifice NG (for 48” Natural Gas Models)

F3468

Air Shutter Orifice NG (for 60” Natural Gas Models)

F3469

Air Shutter Orifice NG (for 72” Natural Gas Models)

F3470

EcoFlow Gas Valve with Step Motor with ECO-LSS-44 for 36” Model

F3515

EcoFlow Gas Valve with Step Motor with ECO-LSS-34 for 48” Model

F3516

EcoFlow Gas Valve with Step Motor with ECO-LSS-27 for 60” Model

F3517

EcoFlow Gas Valve with Step Motor with ECO-LSS-44 for 72” Model

F3471

Natural Gas Regulator, REG-C80K-NG (convertible to LP).

See

Page 33

F3510

Side Mount Pilot Assembly (complete assembly with TC), ECO-VK-Pilot

J7935

Ignition Control Module ( includes 8-pin wire harness), ECO-VK-ECOMOD-WWH

F2694

Tempered Glass Windshield for 36” model (1/4” x 8” x 35-1/2”) (Pkg of 2)

F3474

Tempered Glass Windshield for 48” model (1/4” x 8” x 47-1/2”) (Pkg of 2)

F3475

Tempered Glass Windshield for 60” model (1/4” x 8” x 59-1/2”) (Pkg of 2)

F3476

Tempered Glass Windshield for 72” model (1/4” x 8” x 71-1/2”) (Pkg of 2)

F3477

LED Glass Retainer Clip (2 used per fireplace side) (Pkg of 4)

F3478

Windshield Clips (4 used per single-sided fireplace side) (Pkg of 8)

F3479

5/8” Wire Grommet for LED Lighting (Pkg of 4)

F3480

12-volt adaptor for LED Lighting (Has male & female terminals)

F3481

7.5-volt adaptor for IPI Ecoflow Valve System (Has two female terminals)

F3482

RGB Control Box/Lid Assembly (Fireplace switches and LED dimmer)

F3483

Bottom End (Used to center burner pan into fireplace)

F3484

Pilot Cover (Sits inside bottom end, item #18)

F3518

Ignition Hood with Screen

F3485

NOTE: All items are shipped as one replacement part unless noted in the description.

Summary of Contents for BarcelonaLights36ZEN









































Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands

IHP BarcelonaLights36ZEN, Installation And Operation Instructions Manual

Search results

Summary of Contents for BarcelonaLights36ZEN

Reviews:

Related manuals for BarcelonaLights36ZEN

Brands by name

Popular brands