background image

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

1

HeatFlo™ Kit

GENERAL INFORMATION

The HeatFlo™ system is designed to redirect the convective heat 

of the fireplace from the front of the unit, above the glass, to a 

location higher on the wall. The use of this kit allows for TV instal-

lations closer to the fireplace or in recessed wall cavities above 

the fireplace (see tables 1 and 2 on page 2).
When Installing this kit, reference the framing dimensions and 

follow the framing instructions shown on the fireplace installation 

Instructions. Follow all other installation requirements for the 

fireplace as detailed in the installation manual.

REFER TO INSTALLATION INSTRUCTIONS AND CARE AND 

OPERATIONS MANUAL (IICO) FOR FRAMING DETAILS BEFORE 

INSTALLING THIS KIT.

ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND 

OPERATION MANUAL PROVIDED WITH THE FIREPLACE APPLY 

TO THESE INSTRUCTIONS. 

INSTALLATION INSTRUCTIONS FOR HeatFlo™ Kit

FOR USE IN ASTRIA ALLUMEDLX60TEN, ALLUME60TEN AND SUPERIOR DRL4060TEN FIREPLACES

(This Kit is Compatible for One Sided or See-Thru Application)

HEARTH PRODUCTS 

KITS AND ACCESSORIES

900929-00 REV.  B  05/2019

HeatFlo™ Kit

Catalog 

Number

Model Number

Kit Name

F3780

HTFLO-LIN60

HeatFlo Kit

HeatFlo 

Collar

Gear 

Clamp

Plenum 

Bracket

Flex Pipe 

5” x 26” 

Heat 

Register

HeatFlo 

Register

Trim

TOOLS REQUIRED (not included)

Electric Drill/Driver Gun
Phillips Screwdriver Bits
5/16 Nut Driver
3/8 Nut Driver
Wood Screws

Kit Components

1 ea. Heat Register
1 ea. HeatFlo Register Trim
4 ea. 5” x 26” (compressed length) Flex Pipe
8 ea. Gear Clamp
4 ea. HeatFlo Collar
2 ea. Plenum Bracket
32 ea. Self Tapping Screws

 WARNING 

This kit must be installed by a qualified installer, 

service agency, or gas supplier at the time of the 

fireplace installation. These instructions must 

be used in conjunction with the installation and 

operation manual provided with the fireplace. 

INSTALLER: Leave this manual with the fireplace.

CONSUMER: Retain this manual for future 

reference.

IMPORTANT NOTICE 

HTFLO-LIN60 (HeatFlo) KIT IS REQUIRED IF INSTALLING A 

TV ABOVE THE FIREPLACE.

f i r e - p a r t s . c o m

Summary of Contents for HeatFlo Kit HTFLO-LIN60









Reviews: