background image

 

REPEATER/CROSS- REPEATER 

 4 

   

Rev. : 09/25/2012

 

EC DECLARATION OF CONFORMITY 

The products listed below in the form as delivered are in conformity with the provisions 
of the following European Directives: 

2004/108/EG  Council Directive on the approximation of the laws of the Member States 

relating to electromagnetic compatibility 

CE-marking 2009      

 

Product list: 

K471-CT, K471-MM, K471-SS 

K471-CM, K471-DM, K471-CS, K471-DS, K471-MS 

Conformity to the Directives is assured through the application of the following 
standards: 

EN 55022:  

 

09/2006   Class A 

IEC 61000-4-2:  

 

02/2001 

IEC 61000-4-3:  

 

05/2006 

IEC 61000-4-4:  

 

12/2004 

IEC 61000-4-5

 

11/2006 

 
This declaration certifies the conformity to the specified directives but contains no 
assurance of properties. The safety documentation noted in this manual shall be 
considered in detail. The length of the attached CPU- or Console Cables must not exceed 
3m. The use of suggested interconnect cables is mandatory. 

Oberteuringen, June 23

rd

, 2009 

The management 

 

manufacturer

IHSE GmbH 
Maybachstrasse 11 
88094 Oberteuringen 
Germany 

WARNING: This equipment has been found to comply with the limits for a Class A digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, may cause harmful 
interference to radio communications. Operation of this equipment in a residential area is 
likely to cause harmful interference in which case the user will be required to correct the 
interference at his own expense. 

Summary of Contents for K471-CM
































Reviews: