background image

19

Limited Warranty

The strobe front is warranted against any original manufacturing 
defects for a period of two (2) years from the original date of purchase. 
All other components including the battery pack and smart charger 
are warranted against any original manufacturing defects for a period 
of one (1) year from the original date of purchase.  Defective products 
should be returned to Ikelite postage paid. Ikelite will, at its sole 
discretion, repair or replace such products, and will return to customer 
postage paid. All other claims of any nature are not covered. Except 
as mentioned above, no other warranty expressed or implied applies 
to this Ikelite product.

Service and Repairs

We are most interested in performing any service to ensure that all 
products perform as intended.
No prior authorization is required. You may return directly to us or 
through your dealer. Please include a brief description of the problem, 
any relevant email correspondence, and/or description of the service 
request. Always include name, shipping address, email address, and 
phone number inside of the package. Send postage paid to:

Ikelite Underwater Systems
Attention: Service Department
50 W 33rd St
Indianapolis, IN 46208 USA
+1 (317) 923-4523
ikelite@ikelite.com

For detailed instructions on returning your product for service including 
important information on international customs documentation, please 
refer to our website at: 
https://www.ikelite.com/pages/service-repairs

Summary of Contents for 40230AU





















Reviews: