background image

8

Closing the Housing

1. Place housing face down in your lap or on a flat surface.

2. Check to see that there is an o-ring on the

housing back and that it is clean, and in its

proper location.

3. Guide the back into the housing front. The

o-ring should touch the housing all the way

around. There should be an even gap all

the way around between the housing and

the housing back.

4. Lift the lid snaps so they are extended and

place each lid snap into the corresponding

hook on the housing back. 

5. To close the housing, push down on the lid

snaps until they snap into place. Lid snaps

on opposite sides of the housing should be

closed at the same time. Be sure they are

down far enough to engage the lock. 

Housing Back

O-ring

Housing Back

O-ring

Even gap on

all four sides

Housing

Using the Camera’s Built-in Flash

If you are shooting with the camera’s built-in flash and the camera lens

is set to the widest angle, you may need to zoom the lens slightly or a

dark area may appear in a lower corner of close-up photographs. The

lens port may block some of the light. Install the Diffuser and zoom in

slightly to eliminate any dark areas noted in your photographs  

(You can

test this above water)

. See Diffuser Installation - page 10

.

For the best results, we recommend using an external Ikelite strobe. 
The camera’s built-in flash CANNOT be used with optional Wide-angle or

Accessory lenses.

Summary of Contents for 6183.34 Nikon P340

























Reviews:

Related manuals for 6183.34 Nikon P340